Technical Data Sheet BERGQUIST GAP FILLER TGF 1450 January -2019 PRODUCT DESCRIPTION TYPICAL PROPERTIES OF UNCURED MATERIAL A two-part, high performance, thermally conductive liquid gap Viscosity ,Capillary ,ASTM D5099,Pas *: fillingmaterial. -1 Highshear, Shear Rate 3,000s 30 Viscosity ,Parallel Plate ,ASTM D2196,Pas *: -1 Technology Silicone Low shear, Shear Rate 1 s 200 Appearance (cured) Blue Flow viscosity measured on Parallel Plate Appearance -Part A Blue rheometer. Appearance -Part B Light blue *Part A and B measured separately. Cure Heat cure or Room temperature Density ,ASTM D792,g/cc 1.85 Application Thermal management, Pot life 25C ,ASTM D4473 , minutes 60 TIM(Thermal Interface Material) Mix Ratio by weight: 1 :1 TYPICAL CURE SCHEDULE Part A:Part B Cure Schedule Mix Ratio by volume: 1 :1 5 hours 25C ,ASTM D4473 Part A:Part B 10 minutes 100C ,ASTM D4473 Operating Temperature -60 to 175C Range Alternate Cure Schedule UL Flammability Rating UL 94 V-0 5 hours 25C ,ASTM D4473 30 minutes 100C ,ASTM D4473 FEATURES AND BENEFITS Thermal Conductivity: 1.5W/m-K TYPICAL PROPERTIES OF CURED MATERIAL Ultra- conforming with excellent wet-out for near zero Physical Properties interface stress Hardness, Shore 00,30 second delay, 40 No cure by-products ASTM D2240 Low density for weight sensitive application Heat Capacity ,ASTM D1269,J/g-K 1.0 Excellent low and high temperature mechanical and Electrical Properties chemical stability Dielectric Strength ,ASTM D149,V/mil 275 Shear thinningviscosity for ease of dispensing Dielectric Constant ,ASTM D150,1,000Hz 6.4 10 Volume Resistivity ,ASTM D257,ohm-meter 110 BERGQUIST GAP FILLERTGF 1450 is a high performance, thermally conductive liquid gap fillingmaterial which features Thermal Properties high shear thinning characteristics for optimized consistency Thermal Conductivity ,ASTM D5470 ,W/(m-K) 1.5 and control during dispensing . This material features a low-density design which reduces finalassembly weight . The mixed system will cure at room temperature and can be GENERAL INFORMATION accelerated with the addition of heat . BERGQUIST GAP For safe handling information on this product, consult the Safety Data Sheet, (SDS). FILLERTGF 1450 offers infinitethickness variations with little or no stress to the sensitive components during or following Not for product specifications assembly .As cured, BERGQUIST GAP FILLERTGF 1450 will The technical data contained herein are intended as reference provide a soft, thermally conductive, form-in place elastomer only. Please contact your local quality department for that is ideal for fragileassemblies, capable of fillingunique and assistance and recommendations on specifications for this intricate air voids and gaps . product. The above cure profiles are guideline recommendations. Cure TYPICAL APPLICATIONS conditions (time and temperature) may vary based on Automotive electronics (HEV,NEV, batteries) customers experience and their application requirements, as Lighting well as customer curing equipment, oven loading and actual oven temperatures.TDS BERGQUIST GAP FILLERTGF 1450 , January -2019 CONFIGURATIONS AVAILABLE Disclaimer Note: BERGQUIST GAP FILLERTGF 1450 is available with or The information provided in this Technical Data Sheet (TDS) including the without glass beads. Glass beads are available for order in recommendations for use and application of the product are based on our kits or pail formats knowledge and experience of the product as at the date of this TDS. The product can have a variety of differentapplications as well as differingapplication and BERGQUIST GAP FILLERTGF 1450 is supplied in: working conditions inyour environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended With or without glass beads, available for order inkits applications and results. We strongly recommend that you carry out your own or pail formats prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, THAWING: except ifotherwise explicitly agreed and except inrelation to death or personal 1. Allow container to reach room temperature before use . injury caused by our negligence and any liability under any applicable mandatory product liability law. 2. DO NOT open the container before contents reach 25C In case products are delivered by Henkel Belgium NV, Henkel Electronic temperature. Any moisture that collects on the thawed Materials NV,Henkel Nederland BV, Henkel Technologies France SAS and container should be removed prior to opening the Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, container . Henkels liability will inno event exceed the amount of the concerned delivery. 3. DO NOT re-refrigerate. Once warmed to room In case products are delivered by Henkel Colombiana, S.A.S.the following temperature, the adhesive should not be re-refrigerated . disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the STORAGE recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, Store product in the unopened container in a dry location. therefore, not liable for the suitability of our product for the production processes Storage information may be indicated on the product container and conditions in respect of which you use them, as well as the intended labeling. applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Optimal Storage: 5 to 25C for a 6 month shelf life.Material Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, removed from containers may be contaminated during use. Do except ifotherwise explicitly agreed and except inrelation to death or personal not return product to the original container. HenkelCorporation injury caused by our negligence and any liability under any applicable mandatory cannot assume responsibility for product which has been product liability law. contaminated or stored under conditions other than those In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is previously indicated. Ifadditional information is required, applicable: please contact your local Technical Service Center or The data contained herein are furnished for information only and are believed to Customer Service Representative. be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned Conversions herein and to adopt such precautions as may be advisable for the protection of (C x 1.8)+ 32 =F property and of persons against any hazards that may be involved inthe handling and use thereof. Inlight of the foregoing, Henkel Corporation specifically kV/mm x 25.4 =V/mil disclaims all warranties expressed or implied, including warranties of mm /25.4 =inches merchantability or fitness for a particular purpose, arising from sale or use N x 0.225=lb of Henkel Corporations products. Henkel Corporation specifically N/mm x 5.71=lb/in disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or psi x 145 =N/mm compositions is not to be interpreted as representation that they are free from MPa =N/mm domination of patents owned by others or as a license under any Henkel Nm x 8.851 = lbin Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before Nm x 0.738=lbft repetitive use, using this data as a guide. This product may be covered by one or Nmm x 0.142 =ozin more United States or foreign patents or patent applications. mPas =cP Trademark usage: Except as otherwise noted Alltrademarks inthis document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S. and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics