TechnicalData Sheet BERGQUIST GAP PAD TGP 3000ULM February -2020 PRODUCT DESCRIPTION Electrical Properties 12 A 3.0W/m-K, extremely soft Gap Pad with exceptional thermal Volume Resistivity ,ASTM D257 ,ohm-meter 110 performance at low pressures. DielectricConstant ,ASTM D150 ,1,000Hz 9.2 DielectricBreakdown Voltage ,0.04 inchsample , >6,000 Technology Silicone VAC Appearance Blue Thermal Properties Application Thermal management ,Gap Pad Thermal Conductivity ,ASTM D5470 ,W/(m-K) 3.0 OperatingTemperature -60 to 200C Range Thermal Performance vs. Pressure 2 Thermal Impedance ,ASTM D5470 ,C-in/W: 10% deflection 0.55 FEATURES AND BENEFITS 20% deflection 0.49 Thermal Conductivity: 3.0W/m-K 30% deflection 0.43 High-compliance,low compression stress Ultra low modulus Non-fiberglassoption for applications that require an GENERAL INFORMATION additional reduction instress For safe handling information on this product, consult the Safety Data Sheet, (SDS). TYPICAL APPLICATIONS Telecommunications (routers, switches, base stations) Not for product specifications Opticaltransceivers The technicaldata contained hereinare intended as reference ASICs and DSPs only. Please contact your local quality department for assistance and recommendations on specificationsfor this BERGQUIST GAP PAD TGP 3000ULM isa soft gap filling product. material rated at a thermal conductivity of 3 W/m-K . It is specially formulated for high performance applications CONFIGURATIONS AVAILABLE requiring low assembly stress.The material offers exceptional BERGQUIST GAP PAD TGP 3000ULM is available in the thermal performance at low pressures due to the unique filler following configurations: packageand ultra low modulus resinformulation . Sheet for: 8 x 16 BERGQUIST GAP PAD TGP 3000ULM ishighly conformal to Standard material thicknesses:0.040, 0.060, 0.080, rough or irregular surfaces, allowing excellent wet-out at the 0.100,0.125,0.160inch(1.0,1.5,2.0,2.5,3.18,4.0mm) interface.Protective linersare supplied on both sides allowing for ease of use . The top side has minimal tack for ease of handling. STORAGE Store product in the unopened container in a dry location. Storage information may be indicated on the product container TYPICAL PROPERTIES OF CURED MATERIAL labeling. Physical Properties Optimal Storage: 25 C (3), 50 % RH (10) for a 365 days shelf Hardness, Shore 00,ASTM D2240 20 life.Material removed from containers may be contaminated Density ,ASTM D792,g/cc 2.9 during use. Do not return product to the originalcontainer. InherentSurface Tack2 sided 2 sided HenkelCorporation cannot assume responsibility for product Heat Capacity ,ASTM E1269,J/g-K 0.8 which has been contaminated or stored under conditions other Young s modulus KPa 105 than those previously indicated. Ifadditional information is (psi) (25 ) required, please contact your local TechnicalService Center or Shelflife,days 365 Customer Service Representative. Flammability, UL 94 V-0TDS BERGQUIST GAP PAD TGP 3000ULM , February -2020 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches N x 0.225 = lb/F N/mm x 5.71 = lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkelis, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityinrespect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreed and except inrelation to death or personal injury caused by our negligenceand any liability under any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkelwould be nevertheless held liable,on whatever legalground, Henkelsliabilitywill inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkelis, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trialsto confirm such suitability of our product. Any liabilityinrespect of the information inthe TechnicalData Sheet or any other written or oral recommendation(s) regardingthe concerned product isexcluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligenceand any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained hereinare furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons againstany hazards that may be involved inthe handling and use thereof. Inlight of the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions isnot to be interpreted as representation that they are free from domination of patents owned by others or as a licenseunder any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. Thisproduct may be covered by one or more United States or foreignpatents or patent applications. Trademark usage Except as otherwise noted, alltrademarks inthis document are trademarks of HenkelCorporation inthe U.S.and elsewhere. denotes a trademark registered inthe U.S.Patent and Trademark Office. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics