TechnicalDataSheet BERGQUIST GAP PAD TGP 6000ULM October-2019 PRODUCT DESCRIPTION TYPICAL PROPERTIES OF CURED MATERIAL A high performance, 6 W/m-K siliconethermal interface Young s modulus iscalculatedusing 0.01in/min,step rateof materialwith ultralow modulus. strainwith a sample size 0.79in, after5 minutes of compression at10% strainon a 1mm thicknessmaterial. Technology Silicone Physical Properties Appearance Gray Hardness, Shore000,ASTM D2240 60 ReinforcementCarrierFiberglass HeatCapacity,ASTM E1269,J/g-K 1.0 InterfaceTack 2 sides Density ,Bulk rubber,ASTM D792,g/cc 3.2 Thickness 1.016 to3.175mm Young s Modulus kPa 41.3 Application Thermal management, (psi) (6) TIM(Thermal InterfaceMaterial) FlammabilityRating 0.76 mm ,3.0 mm ,4.7 mm V-0 OperatingTemperature -60 to200C thicknesses,IEC60695-11-10,UL 94 Range UL FlammabilityRating UL 94 V-0 Electrical Properties Dielectric Strength,ASTM D149,VAC >5,000 DielectricConstant,ASTM D150 ,1,000Hz 6.5 FEATURES AND BENEFITS 10 Volume Resistivity,ASTM D257 ,ohm-meter 110 Thermal Conductivity:6.0W/m-K High-compliance,low compression stress Thermal Properties Thermal Conductivity,ASTM D5470 ,W/(m-K) 6.0 Ultralow modulus Thermal Impedance ,0.040 inch 2 ASTM D5470 ,C-in/W: BERGQUIST GAP PAD TGP 6000ULM is an extremely soft 10% Deflection 0.34 gap fillingmaterialratedata thermalconductivity of 6.0W/m-K . Itis specially formulated for high performance applications 20% Deflection 0.29 requiringlow assembly stress .The materialoffers exceptional 30% Deflection 0.26 thermalperformance atlow pressures due tothe unique filler package and ultralow modulus resinformulation.BERGQUIST GAP PAD TGP 6000ULM ishighlyconformal,even tosurfaces GENERAL INFORMATION with highroughness and/ortopography, allowingforexcellent For safe handling information on this product, consult the Safety interfacingand wet-out characteristics. Data Sheet, (SDS). BERGQUIST GAP PAD TGP 6000ULM is offered with a highernatural inherenttack on both sides of the material, Not for product specifications eliminatingthe need for thermally-impeding adhesive layers The technicaldata containedhereinare intendedas reference and allowingfor stick-in-placecharacteristicsduring assembly . only. Please contactyour local quality department for The topside has minimaltackforease of handlingand rework . assistance and recommendations on specificationsfor this BERGQUIST GAP PAD TGP 6000ULM is supplied with product. protectivelinerson bothsides . CONFIGURATIONS AVAILABLE TYPICAL APPLICATIONS BERGQUIST GAP PAD TGP 6000ULM is availableinthe Telecommunications followingconfigurations: ASICs and DSPs Sheet size 8 x 16 Consumer electronics Standard Thicknesses 0.040 ,0.060 ,0.080 , 0.100 , Thermal modules toheatsinks assembly 0.125 Naturaltackbothsides with fiberglass.TDS BERGQUIST GAP PAD TGP 6000ULM , October-2019 STORAGE Disclaimer Note: Storeproduct inthe unopened containerina dry location. The informationprovided inthisTechnicalData Sheet (TDS) includingthe Storageinformationmay be indicatedon theproduct container recommendations for use and applicationof the product are based on our labeling. knowledge and experience of theproduct as atthedate of thisTDS. The product can have a variety of differentapplicationsas well as differingapplicationand OptimalStorage:25 C (3), 50 % RH (10) for a 12 months working conditionsinyour environment thatare beyond our control.Henkel is, therefore,notliableforthesuitabilityof our product fortheproductionprocesses shelf life.Materialremoved from containers may be and conditionsinrespect of which you use them, as well as the intended contaminatedduring use. Do notreturnproduct tothe original applicationsand results. We strongly recommend thatyou carry out your own container.Henkel Corporationcannotassume responsibilityfor priortrialstoconfirmsuch suitabilityof our product. product which has been contaminated or stored under Any liabilityinrespect of theinformationintheTechnicalDataSheet orany other writtenororalrecommendation(s) regardingthe concerned product isexcluded, conditionsotherthan those previously indicated.Ifadditional except ifotherwise explicitlyagreed and except inrelationtodeath orpersonal informationis required, please contactyour localTechnical injury caused by our negligenceand any liabilityunder any applicablemandatory Service CenterorCustomer Service Representative. product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Conversions Incase Henkel would be nevertheless held liable,on whatever legalground, (C x 1.8)+ 32 = F Henkels liabilitywillinno event exceed theamount of theconcerned delivery. kV/mm x 25.4 = V/mil In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: mm /25.4 = inches The informationprovided inthisTechnicalData Sheet (TDS) includingthe N x 0.225 = lb/F recommendations for use and applicationof the product are based on our N/mm x 5.71 = lb/in knowledge and experience of the product as atthe date of thisTDS. Henkel is, psi x 145 = N/mm therefore,notliableforthesuitabilityof our product fortheproductionprocesses and conditionsinrespect of which you use them, as well as the intended MPa = N/mm applicationsand results. We strongly recommend thatyou carry out your own Nm x 8.851 = lbin priortrialstoconfirmsuch suitabilityof our product. Nm x 0.738= lbft Any liabilityinrespect of theinformationintheTechnicalDataSheet orany other Nmm x 0.142= ozin writtenororalrecommendation(s) regardingthe concerned product isexcluded, except ifotherwise explicitlyagreed and except inrelationtodeath orpersonal mPas = cP injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data containedhereinarefurnished forinformationonly and are believed to be reliable.We cannotassume responsibilityforthe results obtainedby others over whose methods we have no control.Itis the user s responsibilityto determinesuitabilityfortheuser s purpose of any productionmethods mentioned hereinand toadopt such precautions as may be advisable forthe protectionof property and of persons againstany hazards thatmay be involved inthehandling and use thereof.Inlightof the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositionsis nottobe interpretedas representationthatthey are free from dominationof patents owned by others or as a license under any Henkel Corporationpatents thatmay cover such processes or compositions.We recommend thateach prospective user test his proposed applicationbefore repetitiveuse, using thisdata as a guide. This product may be covered by one or more UnitedStatesorforeignpatents orpatentapplications. Trademark usage: Except as otherwise noted Alltrademarks inthisdocument are trademarks and/orregisteredtrademarks of Henkel and itsaffiliatesinthe U.S.and elsewhere. Reference N/A Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics