Manual Switches AML91 Series Lamps, Soldering Recommendations, Receptacles AML91 LAMP ORDER GUIDE SOLDERING RECOMMENDATIONS All terminals are solder plated. Proper sol- Lamp Industry Catalog dering and cleaning procedures must be Type Lamp No. Voltage Listing followed to maintain the reliability of AML 86 6.3 AML91LA86 products during installation. An instruc- Incandescent tion sheet which outlines these proce- T-1-3/4 73 14.0 AML91LA73 wedge base dures is included with AML shipments. 85 28.0 AML91LA85 You may also obtain a copy from your MICRO SWITCH Sales Office. Request LAMP DATA PK 8518. The following data was compiled from manufacturers specifications, for refer- As a general guide, the following informa- ence only. tion may be used: INCANDESCENT LAMPS Use a 280C (538F) solder iron tip, up to Industry Life 6 seconds duration, with a 60-40 rosin Lamp No. Volts Amps Watts MSCP A/C Volts core solder. This allows the terminal to heat quickly on the exterior of the housing 86 6.3 .200 1.25 .49 20,000 hours only, and greatly reduces the chance of 5.5 .185 1.12 .246 106,200 hours 5.0 .177 .89 .185 290,000 hours flux migrating inside the housing. 73 14.0 .080 1.12 .30 15,000 hours 12.0 .077 1.00 .23 36,450 hours 85 28.0 .04 1.12 .30 7,000 hours 24.0 .037 .89 .177 41,860 hours Neon Lamps 25,000 hours (half life) LED APPLICATION INFORMATION INTEGRAL LEDs For those devices without internal current LEDs Furnished limiting resistors, suitable external control Peak Inverse Voltage Permanently of the LED current must be provided. It is Installed in w/o Diode w/Diode recommended that a minimum of 5 VDC These Products V I V Protection Protection f f PD open circuit voltage with an appropriate AML12, 15, 16, 2.4 V 20 mA .7 V 5 V 34 V series resistance be used to drive LED de- 22, 25, 26, 42 vices. This minimizes the effect of temper- ature (current variation) on forward volt- AML45 2.4 V 20 mA .7 V 4 V 33 V age of the LED. 100,000 hours (half life). Resistor values can be determined by AML92 SERIES LEDs supply voltage or current for LED: EV f R J S I f For use with these AML switches and in- AML92 ORDER GUIDE dicators equipped with lamp sockets: LED Color Quad Chip Six Chip Pushbutton switches: AML11 (Square WHERE: R J Series Resistance S Only)*, AML21 (rectangular and square), Red AML92ERY AML92ERL E J Supply Voltage and AML31. Green AML92EGY AML92EGL V J Forward Voltage of LED f Paddle switches: AML31/23/33 Yellow AML92EYY AML92EYL I J Circuit Current f Rocker switches: AML14/24/34 Indicators: AML41 White AML92EWL** * Rectangular solid state with one or two lamp circuits If a diode is added in series for reverse ** For use with white or yellow buttons. cannot be used with LED catalog listings ending in polarity protection then: L. EV V f PD OPERATING CHARACTERISTICS R J S I f V Fwd. Voltage (typ.) F I Fwd. V Rev. F R WHERE: V Forward Voltage of PD Type Yellow Green Red White Current Voltage Protection Diode Quad Chip 8.6 8.6 7.8 15 mA 16 V Six Chip 4 V 4 V 4 V 4 V 50 mA 5.6 V TEMPERATURE RANGE (Quad Chip or Six Chip) Operating: 20 to 60C (4 to 140F) Storage: 30 to 100C (22 to 212F) 58 Honeywell1 Sensing and Control1 1-800-537-6945 USA1 F1-815-235-6847 International 1 1-800-737-3360 CanadaX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Industrial Panel Mount Indicators / Switch Indicators category: Click to view products by Honeywell manufacturer: Other Similar products are found below : LW1A-P1-GD LW1A-P1-W 01-931.3 01-152.025 73.362.4028.0 750-1520 9001OA120 A0142N5 A3DT-500Y AL6M-LK3-R AL6M- P7P-A AOLQW-2B0600 AP1M255-A APD106LN-G APD106LN-S APN1126-G APS122DN-W ASLWLD-G ASLWLD-R ATN2100 AYLW4L-A 18-237.035 HW1A-L1-GD HW1A-P2-GL HW1X-BM411-R HW2A-L1-GL HW2A-P1-GD HWAZ1N-OB PA2100/2 PA2200/1 PA2SHIELD PAMR25 LA3P-1C03V-Y 96-923.5 A0244J2 LSPD-120A LSPD-1Y LSPD-6A LSPD-6DA LSPD-6DW LSPD- 6DY LSPD-6R LSPD-6W AL6H-LK3-A AL6H-P4-JW AL6M-LK1-MG AP8M155-G APD106LN-W APN106L-O 21-931.9