HUBER+SUHNER SUCOTEST 18 ASSEMBLY Part no.: ST-18/SMAm/Nm/36 Order no.: 84004594 Electrical specifications Impedance 50 Ohms Operating frequency 18 GHz Velocity of propagation 77% Capacitance 87 pF/m (26.5 pF/ft) Time delay 4.3 ns/m (1.31 ns/ft) 3 Insulation resistance > 5 10 M Dielectric withstand voltage 2 500 V rms Screening effectiveness > 90 dB General specifications Assembly length 914 mm (36 in.) Cable diameter 4.6 mm (0.181 in.) Temperature range -55C to +105C Materials and finishes Preferred bending radius 100 mm (4.0 in.) Cable jacket FEP, blue Connector retention force > 200 N Cable dielectric LDPTFE Recommended mating torque SMA 0.8 Nm... 1.1 Nm Taper sleeves Santoprene / black (7.1 ... 9.7 in.lbs) Marking sleeve Crosslinked polyolefin/white Recommended mating torque N 0.68 Nm... 1.13 Nm Connector contacts Beryllium-copper, gold plated (6.0 ... 10.0 in.lbs) Connector insulation PTFE Connector interface SMA MIL-STD-348A/310 Connector body Stainless steel, passivated Connector interface N MIL-STD-348A/304 Connector nut Stainless steel, passivated Weight 90 gram Gasket Silicon rubber Dimension 36 Electrical table up to 2.01 to 4.01 to 6.01 to 12.01 to 2 GHz 4 GHz 6 GHz 12 GHz 18 GHz Min. return loss (dB) 30 28 25 21 19 Max. insertion loss at 25C (dB) < 0.48 < 0.68 < 0.84 < 1.21 < 1.51 Max. cw power at 25C, sea level (W) > 391 > 277 > 225 > 160 > 131 Max. insertion loss vs. shaking (dB) < 0.03 < 0.03 < 0.03 < 0.03 < 0.03 Max. insertion loss vs. bending (dB) < 0.03 < 0.04 < 0.04 < 0.05 < 0.05 Max. insertion loss vs. torsion (dB) < 0.03 < 0.04 < 0.04 < 0.05 < 0.05 Excellence in connectivity solutionsCare and handling instructions for HUBER + SUHNER microwave cables HUBER + SUHNER microwave cable assemblies of 6. Choose the measurement routing using the largest all types offer a long service life providing they are bend radii possible. Small bend radii may affect treated with the appropriate care and attention. electrical performance. Exceeding the specified Microwave cable assemblies are high precision limits during the measurement process could cause a system components and require proper handling in permanent degradation. order to ensure that measuring performance values are maintained. 7. Avoid twisting microwave cable assemblies. To achieve the maximum measuring performance the Torsion of this type of assembly can alter the relative following guidelines should be followed: diameters of cable layers and affects the electrical characteristics. Exceeding the limit of 10 per metre 1. Assemblies should remain in their original packa- during measuring process could cause a permanent ging for delivery and storage. Storage temperature degradation. should be between -50 C and +80 C and the rela- tive humidity should not exceed 85%. 8. Examine interfaces for damage and/or contami- nation before mating. 2. Carefully unpack assemblies before measure- ment. Avoid kinking cables when straightening from a coil or reel. 9. Discharge connectors before mating or ensure that they are connected to a suitable ground. 3. Ensure that the surroundings are clean and free of dust, dirt and any other particles that could enter 10. When mating connectors with a screwed inter- unsealed connector interfaces. face always hold the connector bodies and turn only the coupling nut. This avoids twisting the cable and ensures minimum wear on the connector pins. 4. Use protective caps to prevent contamination whenever connectors are unmated. 11. Do not exceed the torque specified. 5. Where interfaces are contaminated, particles can be removed with dry, oil-free compressed air. Please use eye-protection. Interfaces can be cleaned with dry cotton swabs. Do not use hard hand-tools or sol- vents. Do not blow into interfaces or use normal compressed-air. The HUBER+SUHNER is certified according to ISO 9001 and ISO 14001. WAIVER HUBER+SUHNER AG While the information contained in this folder has been carefully compiled to the best Mobile Communications+Electronics of our present knowledge, it is not intended as representation or warranty of any kind on our part regarding the suitability of the products concerned for any particular use 9100 Herisau/Switzerland or purpose and neither shall any statement contained herein be construed as a recom- Tel. +41 (71) 353 41 11 mendation to infringe any industrial property rights or as a license to use any such rights. The suitability of each product for any particular purpose must be checked befo- Fax +41 (71) 353 45 90 rehand with our specialists. www.hubersuhner.com Excellence in connectivity solutions 84005174/11.2003, 4353UL/st