3
MICRO Programmable Logic Controller Manual
UNITED STATES
IDEC CORPORATION
1213 Elko Drive
Sunnyvale, CA 94089-2240, USA
Tel (408) 747-0550
Toll Free (800) 262-IDEC
Fax (408) 744-9055
Fax (800) 635-6246
E-mail ideccorp@industry.net
www.industry.net/ideccorp
JAPAN
IDEC IZUMI CORPORATION
7-31, Nishi-Miyahara
1-Chome, Yodogawa-ku
Osaka 532, Japan
Micro Programmable
Tel (06) 398-2571
Fax (06) 392-9731
Logic Controller
CANADA
IDEC CANADA LIMITED
Unit 22-151 Brunel Road
Mississauga, Ontario, L4Z 1X3, Canada
Tel (905) 890-8561
Fax (905) 890-8562
GERMANY
IDEC ELEKTROTECHNIK GmbH
Wendenstrae 331
D-20537 Hamburg, Germany
Tel (040) 25 11 91-93
Fax (040) 25 4 33 61
UNITED KINGDOM
IDEC ELECTRONICS LIMITED
Unit 12, Canbury Business Park
Elm Crescent
Kingston-Upon-Thames
Surrey KT2 6HJ, United Kingdom
Tel (0181) 549-0737
Fax (0181) 546-0963
HONG KONG
IDEC IZUMI (H.K.) CO., LTD.
Room No.1409, Tower 1 Silvercord
30 Canton Road, Tsimshatsui
Kowloon, Hong Kong
Tel (02) 376-2823
Fax (02) 376-0790
TAIWAN
IDEC TAIWAN CORPORATION
3F., No.75, Hsin Tai Wu Road, Sec. 1
Hsi-Chih, Taipei County, Taiwan
Republic of China
Tel (02) 698-2601
Fax (02) 698-2709
AUSTRALIA
IDEC AUSTRALIA PTY. LTD.
2/3 Macro Court
Rowville, Victoria 3178
Australia
Tel (03) 9763-3244
Fax (03) 9763-3255
Users Manual
Users Manual #EM317-0
Printed in the USA 5U 2/97
SAFETY PRECAUTIONS
Read this users manual to make sure of correct operation before starting installation, wiring, operation, maintenance, and
3
inspection of the MICRO .
3
All MICRO s are manufactured under IDECs rigorous quality control system, but users must add a backup or failsafe pro-
3
vision to the control system using the MICRO in applications where heavy damage or personal injury may be caused in
3
case the MICRO should fail.
In this users manual, safety precautions are categorized in order of importance to Warning and Caution:
Warning notices are used to emphasize that improper operation may cause
Warning
severe personal injury or death.
Caution notices are used where inattention might cause personal injury or
Caution
damage to equipment.
Warning
3 3
Turn power off to the MICRO before starting installation, removal, wiring, maintenance, and inspection on the MICRO .
Failure to turn power off may cause electrical shocks or re hazard.
3
Special expertise is required to install, wire, program, and operate the MICRO . People without such expertise must not use
3
the MICRO .
3
Emergency and interlocking circuits must be congured outside the MICRO . If such a circuit is congured inside the
3 3
MICRO , failure of the MICRO may cause disorder of the control system, damage, or accidents.
Caution
3
Install the MICRO according to instructions described in this users manual. Improper installation will result in falling, fail-
3
ure, or malfunction of the MICRO .
3 3
MICRO is designed for installation in equipment. Do not install the MICRO outside of equipment.
3 3 3
Install the MICRO in environments described in this users manual. If the MICRO is used in places where the MICRO is
subjected to high-temperature, high-humidity, condensation, corrosive gases, excessive vibrations, and excessive shocks,
then electrical shocks, re hazard, or malfunction will result.
3 3
The pollution degree of the MICRO is Pollution degree 2. Use the MICRO in environments of pollution degree 2 (accord-
ing to IEC664-1).
3
All DC power type MICRO units are PS2 type (according to EN61131).
3 3
Prevent the MICRO from falling while moving or transporting the MICRO , otherwise damage or malfunction of the
3
MICRO will result.
3 3
Prevent metal fragments and pieces of wire from dropping inside the MICRO housing. Put a cover on the MICRO during
installation and wiring. Ingress of such fragments and chips may cause re hazard, damage, or malfunction.
Use a power supply of the rated value. Use of a wrong power supply may cause re hazard.
Use wires of a proper size to meet voltage and current requirements. Tighten M3 terminal screws to a proper tightening
torque of 0.3 to 0.5 N-m.
3
Use an IEC127-approved fuse on the power line outside the MICRO . This is required when exporting equipment containing
3
MICRO to Europe.
3
Use an IEC127-approved fuse on the output circuit. This is required when exporting equipment containing MICRO to
Europe.
3
Use an EU-approved circuit breaker. This is required when exporting equipment containing MICRO to Europe.
3 3
Make sure of safety before starting and stopping the MICRO or when operating the MICRO to force outputs on or off.
3
Incorrect operation on the MICRO may cause machine damage or accidents.
3
If relays or transistors in the MICRO output circuit fail, outputs may remain on or off. For output signals which may cause
3
heavy accidents, provide a monitor circuit outside of the MICRO .
3 3
Do not connect to the ground directly from the MICRO . Connect a protective ground to the equipment containing MICRO
3
using an M4 or larger screw. This is required when exporting equipment containing MICRO to Europe.
3
Do not disassemble, repair, or modify the MICRO .
3
Dispose of the battery in the MICRO when the battery is dead in accordance with pertaining regulations. When storing or
disposing of the battery, use a proper container prepared for this purpose. This is required when exporting equipment con-
3
taining MICRO to Europe.
3
When disposing of the MICRO , do so as an industrial waste.
Dispose of the battery in the memory card when the battery is dead in accordance with pertaining regulations.
USERS MANUAL PREFACE-1