INDUSTRUINO IND.I/O - PRODUCT DATASHEET. JUNE 2017 Industruino is an Arduino compatible industrial controller. www.industruino.com Ind.I/O Datasheet Installation Ind.I/O Baseboard Pinout Mounting on 35 mm DIN rail, 4 spacing units wide Supply voltage Standard input voltage 12V / 24V permissible range, lower limit (DC) 8 V Analog Analog OUTPUT INPUT permissible range, upper limit (DC) 28 V 2x CH 4x CH Time of day Digital inputs EXPANSION PORT 4-20 mA Number of digital inputs 8 (shared with digital outputs) 14 pin IDC 0-10 V Type of digital input Galvanically isolated serializer with interrupt Input voltage range 0-28V Logic HIGH voltage >11V Logic LOW voltage <3V Maximum trigger frequency 10 KHz Protection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients. Analog Digital outputs zone Number of digital outputs 8 (shared with digital outputs) Type of digital output Galvanically isolated high-side driver (Charge pump NFET) 40 Output voltage range Tied to supply voltage (6.5-32V) Maximum current per output 2.6 A Maximum total current 6.5 A MCU Maximum switching frequency 400 Hz zone Protection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients. Analog inputs Number of analog inputs 4 1 Type of analog inputs Buffered ADC Range of voltage measurement 0-10V Digital Range of current measurement 0-20mA zone Switching of voltage / current mode Automatic - in software Resolution 18Bit Conversion rate 18bit: 3.75 Hz - 16bit: 15 Hz - 14bit: 60 Hz - 12bit: 240 Hz Protection of analog inputs ESD, transients. Analog Outputs Number of analog outputs 2 Type of analog outputs Buffered DAC V+ 6.5-32 V Range of output voltage 0-10V 6.5-32V 8x CH RS485 Range of output current 0-20mA POWER-IN Digital INPUT/OUTPUT Switching of voltage / current mode Automatic - in software Resolution 12Bit Update rate 20 KHz Notes Protection of analog outputs Short-circuit, over-current, over-temperature, ESD, transients. Communication ports Industruino Ind.I/O is the Arduino-compatible equivalent of a PLC. The interface board offers 8 RS485 channels of 24V I/O, 4 channels of 0-10V/4-20mA 18bit ADC, 2 channels of 0-10V/4-20mA 12bit Isolation topology Isolated from MCU and analog field section DAC, isolated RS485 transceiver, isolated power zones. Duplex type Half duplex Number of receivers on bus 32 Data rate 1 Mbps Expansion port (direct MCU control) - Isolation topology Isolated from digital and analog field section dustruino and analog peripherals, the GND line of the analog section should be tied to the GND Number of pins 14 Voltage level 5V Protocols supported SPI, I2C, UART, 9 GPIO s Protection of expansion port ESD, transients. *When operating in an electrically noisy environment it is possible to use a seperate power User Interface supply for your analog peripherals. This will improve the stability of your analog input/output LCD 128x64 pixel FSTN with dimmable backlight Push buttons 3 - push button membrane panel analog supplys GND line. Enviromental Protection class IP20 *The majority of IND.I/O board functions are controlled via i2c, therefore it requires the Indio Ambient operating temperature 0 - 55 C Arduino library which can be found on our websites support page. Dimensions Width 71.5 mm X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for I/O Modules category: Click to view products by Industruino manufacturer: Other Similar products are found below : 70L-IDC5S 70L-OAC-L 70Z3289-4 G21960000700 G21960002700 G34960002700 OACU C4SWOUT PB16H G34960001700 G3TA- OA101SZ-1 DC24 G77-S 5607189 DA5 ODC-24A IDC5P FC6A-N16B1 6421 70MRCQ32-HL G3TAOD201SDC24 C200H-LK201-V1 G3TA-OA202SZ-US DC12 GT1-OD16 GT1-AD04CST B7AM-6BS 70GRCQ24-HS 6422 84110410 GT1-OD16MX G7VC-OC16-B7 70MRCK24-DIN 6202 6402 PI/NI-2D/24 FC6A-J2C1 FC6A-KC1C FC6A-R081 FC6A-J8CU1 GP32900003700 641-480-5022 PB16H 84145010 84110210 FRUSB1601 PCL-720+-BE FRRJ451601 AP24MX3DB25F ADAM-5053S-AE WISE-S614-A C200H-OD211