Product Brief Intel Edison Intel Edison Development Platform Introduction 20 digital input/output pins, Intel Edison Breakout Board including 4 pins as PWM The Intel Edison development Slightly larger than the outputs. platform is designed to lower the Intel Edison module, the 6 analog inputs. barriers to entry for a range of Intel Edison Breakout Board has inventors, entrepreneurs, and a minimal set of features: 1 UART (Rx/Tx). consumer product designers to 2 1 I C. Exposes native 1.8 V I/O of the rapidly prototype and produce Edison module. 1 ICSP 6-pin header (SPI). Internet of Things (IoT) and 0.1 inch grid I/O array of wearable computing products. Micro USB device connector OR through-hole solder points. (via mechanical switch) Intel Edison Board for Arduino* dedicated standard size USB USB OTG with USB Micro host Type-A connector. Type-AB connector. Supports Arduino Sketch, Linux, Micro USB device (connected to USB OTG power switch. Wi-Fi, and Bluetooth. UART). Battery charger. Board I/O: Compatible with SD card connector. Arduino Uno (except 4 PWM USB to device UART bridge with instead of 6 PWM): DC power jack (7 to15 VDC USB micro Type-B connector. input). DC power supply jack (7 to 15 VDC input). Intel IoT Analytics Platform Provides seamless Device-to- Device and Device-to-Cloud communication. Ability to run rules on your data stream that trigger alerts based on advanced analytics. Foundational tools for collecting, storing, and processing data in the cloud. Free for limited and noncommercial use. Intel Edison Development Platform PHYSICAL Form factor Board with 70-pin connector Dimensions 35.5 25.0 3.9 mm (1.4 1.0 0.15 inches) max C/M/F Blue PCB with shields / No enclosure Connector Hirose DF40 Series (1.5, 2.0, or 3.0 mm stack height) Operating temperature 32 to 104F (0 to 40C) EXTERNAL INTERFACES Total of 40 GPIOs, which can be configured as: SD card 1 interface UART 2 controllers (1 full flow control, 1 Rx/Tx) I2C 2 controllers SPI 1 controller with 2 chip selects I2S 1 controller GPIO Additional 12 (with 4 capable of PWM) USB 2.0 1 OTG controller Clock output 32 kHz, 19.2 MHz MAJOR EDISON COMPONENTS SoC 22 nm Intel SoC that includes a dual-core, dual-threaded Intel Atom CPU at 500 MHz and a 32-bit Intel Quark microcontroller at 100 MHz RAM 1 GB LPDDR3 POP memory (2 channel 32bits 800MT/sec) Flash storage 4 GB eMMC (v4.51 spec) WiFi Broadcom* 43340 802.11 a/b/g/n Dual-band (2.4 and 5 GHz) Onboard antenna or external antenna (SKU configurations) Bluetooth Bluetooth 4.0 POWER Input 3.3 to 4.5 V Output 100 ma 3.3 V and 100 ma 1.8 V Power Standby (No radios): 13 mW Standby (Bluetooth 4.0): 21.5 mW (BTLE in Q4-14) Standby (Wi-Fi): 35 mW FIRMWARE + SOFTWARE CPU OS Yocto Linux* v1.6 Development environments Arduino* IDE Eclipse supporting: C, C++, and Python Intel XDK supporting: Node.JS and HTML5 MCU OS RTOS Development environments MCU SDK and IDE Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked reserved or undefined. Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with this information. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Intel literature, may be obtained by calling 1-800-548-4725 or by visiting Intels website at