PD1201 IXYS

PD1201 AC Power Switch INTEGRATED CIRCUITS DIVISION Description Parameter Rating Units The PD1201 is an AC Solid State Switch using optical AC Operating Voltage 120 V rms coupling with dual power SCR outputs to produce an Load Current 1 A rms alternative to optocoupler and Triac circuits. The On-State Voltage Drop 1.2 V rms PD1201 switches are robust enough to provide a (I =1A ) L rms blocking voltage of up to 400V and max surge P current rating of 20A. In addition, tightly controlled Features zero-cross circuitry ensures switching of AC loads Load Current up to 1A without the generation of transients. The input and rms Blocking Voltages up to 400V output circuits are optically coupled to provide P 3750V Input to Output Isolation 3750V of isolation and noise immunity between rms rms 5mA Sensitivity control and load circuits. As a result the PD1201 Zero-Crossing Detection is well suited for industrial environments where DC Control, AC Output electromagnetic interference would disrupt the Optically Isolated operation of electromechanical relays. TTL and CMOS Compatible Low EMI and RFI Generation Approvals High Noise Immunity UL Recognized Component: UL 508 File E69938 VDE compatible CSA Certified Component: File 043639 Machine Insertable, Wave Solderable Applications Ordering Information Programmable Control Process Control Part Description Power Control Panels PD1201 4-Pin (16-Pin Body) DIP Package (25/Tube) Remote Switching Gas Pump Electronics Contactors Pin Configuration Large Relays Solenoids Motors 1 16 Heaters + LED - LED ZC 10 AC Load 8 AC Load DS-PD1201-R14 1 www.ixysic.comPD1201 INTEGRATED CIRCUITS DIVISION Absolute Maximum Ratings 25C Absolute Maximum Ratings are stress ratings. Stresses in Parameter Min Max Units excess of these ratings can cause permanent damage to Blocking Voltage - 400 V P the device. Functional operation of the device at conditions Reverse Input Voltage - 5 V beyond those indicated in the operational sections of this Input Control Current - 100 mA data sheet is not implied. Peak (10ms) - 1 A 1 Input Power Dissipation - 150 mW 2 Total Package Dissipation - 1600 mW Isolation Voltage, Input to Output 3750 - V rms Operational Temperature -40 +85 C Storage Temperature -40 +125 C 1 Derate linearly 1.33 mW / C 2 Derate linearly 16.6 mW / C Electrical Characteristics 25C Parameter Conditions Symbol Min Typ Max Units Output Characteristics AC Operating Voltage I =5mA V 20 - 120 V F OP rms Load Current (Continuous) V =120-240VAC I 0.005 - 1 A L L rms Maximum Surge Current t<16ms I - - 20 A PEAK Off-State Leakage Current V =400V I -- 1 mA L DC LEAK On-State Voltage Drop I =1.0A - - - 1.2 V L rms rms Critical Rate of Rise - dV/dt 1000 1200 - V/s Switching Speeds Turn-On t - - 0.5 on I =5mA Cycles F Turn-Off t - - 0.5 off 1 st Zero-Cross Turn-On Voltage 1 half-cycle -2 5 V - Subsequent half-cycle - - 1 V Operating Frequency - - 20 - 500 Hz 2 Load Power Factor for Guaranteed Turn-On - PF 0.25 - - - Capacitance Input-To-Output - C -3 - pF I/O Input Characteristics Input Control Current For Normal Environment - -- 5 I mA F For High Noise Environment - - - 10 Input Voltage Drop I =5mA V 0.9 1.2 1.4 V F F Input Dropout Voltage - - 0.8 - - V Reverse Input Current V =5V I - - 10 A R R 1 st Zero Cross 1 half-cycle < 100Hz. 2 Snubber circuits may be required at low power factors. R14 2 www.ixysic.com