Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), Ultra-Stable X8R Dielectric, 10 100 VDC (Commercial & Automotive Grade) Overview KEMETs Flexible Termination (FT-CAP) Multilayer Ceramic (KPS) product lines by providing a complete portfolio of flex Capacitor in Ultra-Stable X8R dielectric incorporates a mitigation solutions. unique, flexible termination system that is integrated with Combined with the stability of KEMETs Ultra-Stable high KEMETs standard termination materials. A conductive temperature dielectric technology, these flex-robust devices silver epoxy is utilized between the base metal and nickel are RoHS Compliant, offer up to 5 mm of flex-bend capability barrier layers of KEMETs standard termination system and feature a 150C maximum operating temperature. in order to establish pliability, while maintaining terminal Ultra-Stable X8R dielectric offers the same temperature strength, solderability and electrical performance. capability as conventional X8R, but without the capacitance This technology was developed in order to address the loss due to applied DC voltage. These devices exhibit no primary failure mode of MLCCs flex cracks, which are change in capacitance with respect to voltage and boast a typically the result of excessive tensile and shear stresses minimal change in capacitance with reference to ambient produced during board flexure and thermal cycling. Flexible temperature. They are also suitable replacements for higher termination technology inhibits the transfer of board stress capacitance and larger footprint devices that fail to offer to the rigid ceramic body, therefore mitigating flex cracks capacitance stability. Capacitance change with respect to which can result in low IR or short circuit failures. temperature is limited to 15% from 55C to +150C. Although this technology does not eliminate the potential In addition to Commercial Grade, Automotive Grade devices for mechanical damage that may propagate during extreme are available which meet the demanding Automotive environmental and handling conditions, it does provide Electronics Council s AEC-Q200 qualification requirements. superior flex performance over standard termination systems. FT-CAP complements KEMETs Open Mode, Floating Electrode (FE-CAP), Floating Electrode with Flexible Termination (FF-CAP), and KEMET Power Solutions Ordering Information C 1206 X 104 J 3 H A C AUTO Reated Failure Packaging/ Case Size Specification/ Capacitance Capacitance 1 Ceramic Voltage Dielectric Rate/ Termination Finish Grade ( x ) Series Code (pF) Tolerance (VDC) Design (C-Spec) 0603 X = Flexible Two B = 0.10 pF 8 = 10 H = Ultra- A = C = 100% Matte Sn See 0805 Termination significant C = 0.25 pF 4 = 16 Stable X8R N/A L = SnPb (5% Pb minimum)Packaging 1206 digits and D = 0.5 pF 3 = 25 C-Spec 1210 number of F = 1% 5 = 50 Ordering 1812 zeros. G = 2% 1 = 100 Options Tabl J = 5% K = 10% M = 20% 1 Additional termination finish options may be available. Contact KEMET for details. 1 SnPb termination finish option is not available on Automotive Grade product. Built Into Tomorrow KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1063 X8R FT-CAP SMD 10/28/2020 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), Ultra-Stable X8R Dielectric, 10 100 VDC (Commercial & Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade Packaging Type Ordering Code (C-Spec) 1 Commercial Grade Bulk Bag Not Required (Blank) 7 Reel/Unmarked TU 7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked 7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 7081 2 13 Reel/Unmarked/2 mm pitch 7082 3 Automotive Grade 7 Reel AUTO AUTO7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked AUTO7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 3190 2 13 Reel/Unmarked/2 mm pitch 3191 1 Default packaging is Bulk Bag. An ordering code C-Spec is not required for Bulk Bag packaging. 1 The terms Marked and Unmarked pertain to laser marking option of capacitors. All packaging options labeled as Unmarked will contain capacitors that have not been laser marked. 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see Tape & Reel Packaging Information. 3 Reeling tape options (Paper or Plastic) are dependent on capacitor case size (L x W) and thickness dimension. See Chip Thickness/Tape & Reel Packaging Quantities and Tape & Reel Packaging Information. 3 For additional Information regarding AUTO C-Spec options, see Automotive C-Spec Information. 3 All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For more information see Capacitor Marking. Benefits 55C to +150C operating temperature range High thermal stability Superior flex performance (up to 5 mm) High ripple current capability Lead (Pb)-free, RoHS and REACH compliant No capacitance change with respect to applied rated DC EIA 0603, 0805, 1206, 1210, and 1812 case sizes voltage DC voltage ratings of 10 V, 16 V, 25 V, 50 V and 100 V Non-polar device, minimizing installation concerns Capacitance offerings ranging from 0.5 pF to 0.22 F Commercial and Automotive (AECQ200) grades available Available capacitance tolerances of 0.10 pf, 0.25 pf, 100% pure matte tin-plated termination finish allowing for 0.5 pf, 1%, 2%, 5%, excellent solderability 10%, and 20% SnPb plated termination finish option available upon Extremely low ESR and ESL request (5% Pb minimum) Applications Typical applications include decoupling, bypass, filtering and transient voltage suppression in critical and safety relevant circuits without (integrated) current limitation, including those subject to high levels of board flexure or temperature cycling. KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1063 X8R FT-CAP SMD 10/28/2020 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com