Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS, X7R Dielectric, 10 250 VDC (Automotive Grade) Overview KEMET Power Solutions (KPS) Automotive Series stacked capable of Pb-Free reflow profiles and provide lower ESR, ESL capacitors utilize a proprietary lead-frame technology and higher ripple current capability when compared to other to vertically stack one or two multilayer ceramic chip dielectric solutions. capacitors into a single compact surface mount package. The attached lead-frame mechanically isolates the Combined with the stability of an X7R dielectric, KEMETs capacitor/s from the printed circuit board, therefore offering KPS Series devices exhibit a predictable change in advanced mechanical and thermal stress performance. capacitance with respect to time and voltage and boast a Isolation also addresses concerns for audible, microphonic minimal change in capacitance with reference to ambient noise that may occur when a bias voltage is applied. A temperature. Capacitance change is limited to 15% from two chip stack offers up to double the capacitance in 55C to +125C. the same or smaller design footprint when compared to traditional surface mount MLCC devices. Providing up to KPS Series automotive grade capacitors meet the demanding 10 mm of board flex capability, KPS Series capacitors are Automotive Electronics Council s AECQ200 qualification environmentally friendly and in compliance with RoHS requirements. legislation. Available in X7R dielectric, these devices are Benefits AECQ200 automotive qualified 55C to +125C operating temperature range Reliable and robust termination system EIA 1210, 1812, and 2220 Case sizes DC voltage ratings of 10 V, 16 V, 25 V, 50 V, 100 V, and 250 V Ordering Information C 2220 C 106 M 5 R 2 C AUTO Rated Case Size Specification/ Capacitance Capacitance Packaging/Grade 2 Ceramic Voltage Dielectric Failure Rate/Design Leadframe Finish 1 ( x ) Series Code (pF) Tolerance (C-Spec) (VDC) 1210 C = Standard Two K = 10% 8 = 10 R = X7R 1 = KPS Single C = 100% Matte Sn See 1812 significant M = 20% 4 = 16 Chip Stack Packaging 2220 digits and 3 = 25 2 = KPS Double C-Spec number of 5 = 50 Chip Stack Ordering zeros 1 = 100 Options Table A = 250 1 Double chip stacks 2 in the 13th character position of the ordering code) are only available in M (20%) capacitance tolerance. Single chip stacks 1 in the 13th character position of the ordering code) are available in K (10%) or M (20%) tolerances. 2 Additional leadframe finish options may be available. Contact KEMET for details. Built Into Tomorrow KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1021 X7R KPS AUTO SMD 6/28/2021 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS, X7R Dielectric, 10 250 VDC (Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade 1 Packaging Type 2 Ordering Code (C-Spec) 7 Reel (Embossed Plastic Tape)/Unmarked AUTO 13 Reel (Embossed Plastic Tape)/Unmarked AUTO 7289 1 The termsMarke andUnmarke pertain to laser marking option of capacitors. All packaging options labeled asUnmarke will contain capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information seeCapacitor Markin. 2 For additional information regardingAUT C-Spec options, seeAutomotive C-Spec Informatio. Benefits cont. Capacitance offerings ranging from 0.1F up to 47 F Reduces audible, microphonic noise Available capacitance tolerances of 10% and 20% Extremely low ESR and ESL Higher capacitance in the same footprint Lead (Pb)-free, RoHS and REACH compliant Potential board space savings Capable of Pb-free reflow profiles Advanced protection against thermal and Non-polar device, minimizing installation concerns mechanical stress Tantalum and electrolytic alternative Provides up to 10 mm of board flex capability Applications Typical applications include smoothing circuits, DC/DC converters, power supplies (input/output filters), noise reduction (piezoelectric/mechanical), circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Qualification/Certification Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AECQ200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AECQ200, please visit their website at www.aecouncil.com. Environmental Compliance Lead (Pb)-free, RoHS, and REACH compliant without exemptions. KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1021 X7R KPS AUTO SMD 6/28/20221 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com