APFA3010SURKCGKSYKC Kingbright

APFA3010SURKCGKSYKC 3.0 x 1.0 mm Right Angle SMD Chip LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip Yellow Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES 3.0 x 1.5 x 1.0 mm right angle SMD LED, 1.0 mm thickness Low power consumption Wide viewing angle Ideal for backlight and indicator Package: 2000 pcs / reel Moisture sensitivity level: 3 RECOMMENDED SOLDERING PATTERN Halogen-free (units : mm tolerance : 0.1) Tinned pads for improved solderability RoHS compliant APPLICATIONS Backlight Status indicator Home and smart appliances Wearable and portable devices Healthcare applications Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.2(0.008 ) unless otherwise noted. ATTENTION 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. Observe precautions for handling 4. The device has a single mounting surface. The device must be mounted according to the specifications. electrostatic discharge sensitive devices SELECTION GUIDE 2 1 Iv (mcd) 20mA Viewing Angle Emitting Color Part Number Lens Type (Material) Min. Typ. 21/2 120 220 Hyper Red (AlGaInP) *55 *80 20 45 APFA3010SURKCGKSYKC Green (AlGalnP) Water Clear 150 *20 *45 120 180 Super Bright Yellow (AlGaInP) *120 *180 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 4 2021 Kingbright. All Rights Reserved. Spec No: DSAI9517 / 1203004300 Rev No: V.7A Date: 01/05/2021 APFA3010SURKCGKSYKC ELECTRICAL / OPTICAL CHARACTERISTICS at T =25C A Value Parameter Symbol Emitting Color Unit Typ. Max. Hyper Red 645 Wavelength at Peak Emission I = 20mA Green 574 - nm F peak Super Bright Yellow 590 Hyper Red 630 1 Dominant Wavelength I = 20mA Green 570 - nm F dom Super Bright Yellow 590 Hyper Red 28 Spectral Bandwidth at 50% REL MAX Green 20 - nm I = 20mA F Super Bright Yellow 20 Hyper Red 35 Capacitance C Green 15 - pF Super Bright Yellow 20 Hyper Red 1.95 2.5 2 Forward Voltage I = 20mA V Green 2.1 2.5 V F F Super Bright Yellow 2 2.5 Hyper Red 10 Reverse Current (V = 5V) I Green - 10 A R R Super Bright Yellow 10 Hyper Red 0.14 Temperature Coefficient of peak TC Green 0.12 - nm/C peak I = 20mA, -10C T 85C F Super Bright Yellow 0.12 Hyper Red 0.05 Temperature Coefficient of dom TC Green 0.08 - nm/C dom I = 20mA, -10C T 85C F Super Bright Yellow 0.07 Hyper Red -1.9 Temperature Coefficient of V F TC Green -1.9 - mV/C V I = 20mA, -10C T 85C F Super Bright Yellow -1.9 Notes: 1. The dominant wavelength (d) above is the setup value of the sorting machine. (Tolerance d: 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25C A Value Parameter Symbol Unit Super Bright Hyper Red Green Yellow Power Dissipation P 75 75 75 mW D Reverse Voltage V 5 5 5 V R Junction Temperature T 115 115 115 C j Operating Temperature T -40 to +85 C op Storage Temperature T -40 to +85 C stg DC Forward Current I 30 30 30 mA F 1 Peak Forward Current I 185 150 175 mA FM Electrostatic Discharge Threshold (HBM) 3000 3000 3000 V - 2 Thermal Resistance (Junction / Ambient) R 610 710 790 C/W th JA 2 Thermal Resistance (Junction / Solder point) R 500 600 680 C/W th JS Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2 2. R ,R Results from mounting on PC board FR4 (pad size 16 mm per pad). th JA th JS 3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 4 2021 Kingbright. All Rights Reserved. Spec No: DSAI9517 / 1203004300 Rev No: V.7A Date: 01/05/2021