6.2mm (0.25INCH) FOUR DIGIT NUMERIC DISPLAY Part Number: CC25-12SURKWA Hyper Red Features Description z 0.25 inch digit height The Hyper Red source color devices are made with Al- z Low current operation. GaInP on GaAs substrate Light Emitting Diode. z Excellent character appearance. z Easy mounting on P.C. boards or sockets. z Categorized for luminous intensity. z Mechanically rugged. z Standard : gray face, white segment. z RoHS compliant. Package Dimensions& Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is 0.25(0.01 )unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAK2807 REV NO: V.6A DATE: JUN/28/2016 PAGE: 1 OF 7 APPROVED: Wynec CHECKED: Joe Lee DRAWN: L.T.Zhang ERP: 1304000564 KingbrightSelection Guide Iv (ucd) 1 10mA Part No. Emitting Color (Material) Lens Type Description Min. Typ. 31000 80000 CC25-12SURKWA Hyper Red (AlGaInP) White Diffused Common Cathode *14000 *24000 Notes: 1. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions Peak Wavelength Hyper Red 645 nm IF=10mA peak Dominant Wavelength Hyper Red 630 nm IF=10mA D 1 Spectral Line Half-width Hyper Red 28 nm IF=10mA 1/2 C Capacitance Hyper Red 35 pF VF=0V f=1MHz Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 Forward D1,D2,D3,D4,D5,D6,D8 VF 2 Hyper Red 1.85 2.5 V IF=10mA Voltage D7,L Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 10 Reverse D1,D2,D3,D4,D5,D6,D8 IR Hyper Red uA VR = 5V Current D7,L 20 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter Values Units Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 75 Power D1,D2,D3,D4,D5,D6,D8 mW dissipation D7,L 150 Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 30 DC Forward D1,D2,D3,D4,D5,D6,D8 mA Current D7,L 60 Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 Reverse D1,D2,D3,D4,D5,D6,D8 Voltage 5 V D7,L Dig1 8, Dig2 8 ,Dig3 8 ,Dig4 8 185 Peak Forward D1,D2,D3,D4,D5,D6,D8 mA Current 1 D7,L 370 Operating/Storage Temperature -40C To +85C Lead Solder Temperature 2 260C For 3~5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAK2807 REV NO: V.6A DATE: JUN/28/2016 PAGE: 2 OF 7 APPROVED: Wynec CHECKED: Joe Lee DRAWN: L.T.Zhang ERP: 1304000564 Kingbright