KPGF-0606GBRC-120 Kingbright

0.65x0.65mm FULL-COLOR SURFACE MOUNT LED PRELIMINARY SPEC Part Number: KPGF-0606GBRC-120 ATTENTION Green OBSERVE PRECAUTIONS Blue FOR HANDLING Hyper Red ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 0.65mmX0.65mm SMD LED, 0.2mm thickness. z The Green source color devices are made with InGaN on z Low power consumption. SiC substrate Light Emitting Diode. z Can produce any color in visible spectrum. z The Blue source color devices are made with InGaN on z Package : 4000pcs / reel. SiC substrate Light Emitting Diode. z Moisture sensitivity level : level 3. z The Hyper Red source color devices are made with z Low current IF=5mA operating. AlGaInP on GaAs substrate Light Emitting Diode. z RoHS compliant. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.1(0.004 ) unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO2565 REV NO: V.1B DATE: AUG/31/2015 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015078 Selection Guide Iv (mcd) 2 Viewing 5mA Angle 1 Part No. Emitting Color (Material) Lens Type Min. Typ. 2 1/2 Green (InGaN) 30 90 145 KPGF-0606GBRC-120 Blue (InGaN) Water Clear 5 20 140 Hyper Red (AlGaInP) 10 30 130 Notes: 1. 1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions Green 518 peak Peak Wavelength Blue 461 nm IF=5mA Hyper Red 632 Green 527 D 1 Dominant Wavelength Blue 467 nm IF=5mA Hyper Red 624 Green 35 1/2 Spectral Line Half-width Blue 22 nm IF=5mA Hyper Red 20 Green 3 3.2 VF 2 Forward Voltage Blue 2.9 3.1 V IF=5mA Hyper Red 1.95 2.3 Green 100 C Capacitance Blue 110 pF VF=0V f=1MHz Hyper Red 25 Green 50 IR Reverse Current Blue 50 uA VR=5V Hyper Red 10 Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter Green Blue Hyper Red Units Power dissipation 1 35 mW DC Forward Current 2 10 10 10 mA Peak Forward Current 3 50 50 50 mA Electrostatic Discharge Threshold (HBM) 1000 1000 3000 V Reverse Voltage 5 V Operating Temperature -40C To +85C Storage Temperature -40C To +100C Notes: 1. Within 35mW when multiple chips are lightened 2. The maximum ratings are valid for the case of lighting a single chip When two chips are lit at the same time, each chip should be driven at a current lower than 50% of the absolute maximum ratings When three chips are lit at the same time, each chip should be driven at a current lower than 30% of the absolute maximum ratings 3. Duty Cycle 1 / 20, Pulse Width=1ms. SPEC NO: DSAO2565 REV NO: V.1B DATE: AUG/31/2015 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015078