X-On Electronics has gained recognition as a prominent supplier of WP59BL/GYW LED Circuit Board Indicators across the USA, India, Europe, Australia, and various other global locations. WP59BL/GYW LED Circuit Board Indicators are a product manufactured by Kingbright. We provide cost-effective solutions for LED Circuit Board Indicators, ensuring timely deliveries around the world.
We are delighted to provide the WP59BL/GYW from our LED Circuit Board Indicators category, at competitive rates not only in the United States, Australia, and India, but also across Europe and beyond. A long established and extensive electronic component distribution network has enhanced our global reach and dependability, ensuring cost savings through prompt deliveries worldwide. Client satisfaction is at the heart of our business, where every component counts and every customer matters. Our technical service team is ready to assist you. From product selection to after-sales support, we strive to deliver a seamless and satisfying experience. Are you ready to experience the best in electronic component distribution? Contact X-ON Electronics today and discover why X-On are a preferred choice for the WP59BL/GYW and other electronic components in the LED Circuit Board Indicators category and beyond.
WP59BL/GYW T-1 3/4 (5mm) Single-Level Circuit Board Indicator DESCRIPTIONS PACKAGE DIMENSIONS The Green source color devices are made with Gallium Phosphide Green Light Emitting Diode The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode FEATURES Pre-trimmed leads for pc board mounting Black case enhances contrast ratio High reliability-life measured in years Housing UL rating: 94V-0 Housing material: Type 66 nylon RoHS compliant APPLICATIONS Status indicator Illuminator Signage applications Decorative and entertainment lighting Commercial and residential architectural lighting Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01 ) unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SELECTION GUIDE 2 1 Iv (mcd) 20mA Viewing Angle Emitting Color Part Number Lens Type (Material) Min. Typ. 21/2 50 100 Green (GaP) WP59BL/GYW White Diffused 30 Yellow (GaAsP/GaP) 20 40 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 4 2021 Kingbright. All Rights Reserved. Spec No: DSAF2083 / 1102001728 Rev No: V.9B Date: 07/13/2021 WP59BL/GYW ELECTRICAL / OPTICAL CHARACTERISTICS at T =25C A Value Parameter Symbol Emitting Color Unit Typ. Max. Green 565 Wavelength at Peak Emission I = 20mA - nm F peak Yellow 590 Green 568 1 Dominant Wavelength I = 20mA - nm F dom Yellow 588 Spectral Bandwidth at 50% REL MAX Green 30 - nm I = 20mA Yellow 35 F Green 15 Capacitance C - pF Yellow 20 Green 2.2 2.5 2 Forward Voltage I = 20mA V V F F Yellow 2.1 2.5 Green 10 Reverse Current (V = 5V) I - A R R Yellow 10 Notes: 1. The dominant wavelength (d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25C A Value Parameter Symbol Unit Green Yellow Power Dissipation P 62.5 75 mW D Reverse Voltage V 5 5 V R Junction Temperature T 110 110 C j Operating Temperature T -40 to +85 C op Storage Temperature T -40 to +85 C stg DC Forward Current I 25 30 mA F 1 Peak Forward Current I 140 140 mA FM Electrostatic Discharge Threshold (HBM) 8000 8000 V - 2 Lead Solder Temperature 260C For 3 Seconds 3 Lead Solder Temperature 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 4 2021 Kingbright. All Rights Reserved. Spec No: DSAF2083 / 1102001728 Rev No: V.9B Date: 07/13/2021