WP7113LSECK/J3 Kingbright

WP7113LSECK/J3 T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS The Hyper Red device is based on light emitting diode chip made from AlGaInP Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES Low power consumption Popular T-1 3/4 diameter package General purpose leads Reliable and rugged Long life - solid state reliability Available on tape and reel RoHS compliant APPLICATIONS Status indicator Illuminator Signage applications Decorative and entertainment lighting Commercial and residential architectural lighting Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01 ) unless otherwise noted. ATTENTION 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change Observe precautions for handling electrostatic discharge sensitive devices SELECTION GUIDE 2 1 Iv (mcd) 2mA Viewin g Angle Emitting Color Part Number Lens Type (Material) Min. Typ. 21/2 320 800 Hyper Red WP7113LSECK/J3 Water Clear 20 (AlGaInP) *180 *550 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 5 2021 Kingbright. All Rights Reserved. Spec No: DSAN8286 / 1101033255 Rev No: V.5A Date: 07/13/2021 WP7113LSECK/J3 ELECTRICAL / OPTICAL CHARACTERISTICS at T =25C A Value Parameter Symbol Emitting Color Unit Min. Typ. Max. Wavelength at Peak Emission I = 2mA Hyper Red - 640 - nm F peak 1 Dominant Wavelength I = 2mA Hyper Red - 625 - nm F dom Spectral Bandwidth at 50% REL MAX Hyper Red - 20 - nm I = 2mA F Capacitance C Hyper Red - 27 - pF 2 Forward Voltage I = 2mA V Hyper Red 1.5 1.8 2.1 V F F Reverse Current (V = 5V) I Hyper Red - - 10 A R R Notes: 1. The dominant wavelength (d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25C A Parameter Symbol Value Unit Power Dissipation P 84 mW D Reverse Voltage V 5 V R Junction Temperature T 115 C j Operating Temperature T -40 to +85 C op Storage Temperature T -40 to +85 C stg DC Forward Current I 30 mA F 1 Peak Forward Current I 150 mA FM Electrostatic Discharge Threshold (HBM) 3000 V - 2 Lead Solder Temperature 260C For 3 Seconds 3 Lead Solder Temperature 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 5 2021 Kingbright. All Rights Reserved. Spec No: DSAN8286 / 1101033255 Rev No: V.5A Date: 07/13/2021