F91-AJ6 Series Automotive Product Range F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range FEATURES Compliant to the RoHS3 directive 2015/863/EU Compliant to AEC-Q200 100% Surge Current Tested LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS Cabin Electronics Infotainment CASE DIMENSIONS: millimeters (inches) EIA L 0.20 W 0.20 (0.008) H 0.20 (0.008) W 0.20 A 0.30 (0.012) 1 Code EIA Code S Min. Metric (0.008) -0.10 (0.004) -0.10 (0.004) (0.008) -0.20 (0.008) A 1206 3216-18 3.20 (0.126) 1.60 (0.063) 1.60 (0.063) 1.20 (0.047) 0.80 (0.031) 1.10 (0.043) B 1210 3528-21 3.50 (0.138) 2.80 (0.110) 1.90 (0.075) 2.20 (0.087) 0.80 (0.031) 1.40 (0.055) N 2917 7343-31 7.30 (0.287) 4.30 (0.169) 2.90 (0.114) 2.40 (0.094) 1.30 (0.051) 4.40 (0.173) W dimension applies to the termination width for a dimensional area only 1 A, B, N CASE Capacitance Value in pF AVX LOGO 476 = 47F Rated Voltage Code Polarity 476 A A = 10V Band xxxxx ID Code (Anode+) 4V 16V 35V V G C 6.3V J 20V D 10V A 25V E *Capacitance code of P case products are as shown below. HOW TO ORDER 1C M AJ6 F91 226 B Type Rated Capacitance Code Tolerance Case Packaging Tolerance pF code: 1st two K = 10% See Tape & Reel K = 10% Voltage Size digits represent M = 20% Packaging Section M = 20% See significant figures, table 3rd digit represents above multiplier (number of zeros to follow) TECHNICAL SPECIFICATIONS Category Temperature Range -55 to +125C Rated Temperature +85C Capacitance Tolerance 20%, 10% at 120Hz Dissipation Factor Refer to next page ESR 100kHz Refer to next page After 1 minutes application of rated voltage, leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. After 1 minutes application of rated voltage, leakage current at 85C is not Leakage Current more than 0.1CV or 5A, whichever is greater. After 1 minutes application of derated voltage, leakage current at 125C is not more than 0.125CV or 6.3A, whichever is greater. +15% Max. at +125C Capacitance Change By Temperature +10% Max. at +85C -10% Max. at -55C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 88 090121F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage *1: C/C Marked * F Code 6.3V (0J) 10V (1A) 16V (1C) 10 106 A A Item All Case (%) 22 226 A A B Damp Heat 10 33 336 B B Temperature cycles 10 47 476 A,B B Resistance soldering heat 10 100 107 B N Surge 10 220 227 N Endurance 10 Released ratings RATINGS & PART NUMBER REFERENCE Rated DF ESR 100kHz RMS Current (mA) *1 AVX Capacitance Case Size Voltage DCL (A) 120Hz 100kHz C/C MSL Part No. (F) (V) (%) (m) 25C 85C 125C (%) 6.3 Volt F910J226 AAAJ6 A 22 6.3 1.4 8 1250 245 220 98 * 3 F910J476 AAAJ6 A 47 6.3 3.0 18 1250 245 220 98 * 3 F910J476 BAAJ6 B 47 6.3 3.0 6 500 412 371 165 * 3 F910J107 BAAJ6 B 100 6.3 6.3 14 450 435 391 174 * 3 10 Volt F911A106 AAAJ6 A 10 10 1.0 6 1500 224 201 89 * 3 F911A226 AAAJ6 A 22 10 2.2 12 1250 245 220 98 * 3 F911A336 BAAJ6 B 33 10 3.3 8 700 348 314 139 * 3 F911A476 BAAJ6 B 47 10 4.7 8 500 412 371 165 * 3 F911A227 NCAJ6 N 220 10 22.0 12 100 1225 1102 490 * 3 16 Volt F911C106 AAAJ6 A 10 16 1.6 6 1500 224 201 89 * 3 F911C226 BAAJ6 B 22 16 3.5 8 950 299 269 120 * 3 F911C336 BAAJ6 B 33 16 5.3 8 950 299 269 120 * 3 F911C107 NCAJ6 N 100 16 16.0 10 100 1225 1102 490 * 3 : for 20% tolerance, for 10% tolerance.Moisture Sensitivity Level (MSL) is defined according to J-STD-020. QUALIFICATION TABLE F91-AJ6 series (Temperature range -55C to +125C) TEST Condition At 40C, 90 to 95% R.H., 500 hours (No voltage applied) Damp Heat Capacitance Change .................. Refer to the table above (*1) Dissipation Factor ....................... Initial specified value or less (Steady State) Leakage Current .......................... Initial specified value or less After 1000 hours application of rated voltage in series with a 33 resistor at 85C, 85% R.H., capacitors meet the characteristics requirements table below. Capacitance Change .................. Refer to the table above (*1) Load Humidity Dissipation Factor ....................... Initial specified value or less Leakage Current .......................... 125% or less than the initial specified value At -55C / +125C, 30 minutes each, 1000 cycles Capacitance Change .................. Refer to the table above (*1) Temperature Cycles Dissipation Factor ....................... Initial specified value or less Leakage Current .......................... Initial specified value or less 10 seconds reflow at 260C, 10 seconds immersion at 260C. Capacitance Change .................. Refer to the table above (*1) Resistance to Soldering Heat Dissipation Factor ....................... Initial specified value or less Leakage Current .......................... Initial specified value or less After application of surge voltage in series with a 33 resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ....................Refer to the table above (*1) Surge Dissipation Factor ......................... Initial specified value or less Leakage Current ...........................Initial specified value or less After 2000 hours application of rated voltage in series with a 3 resistor at 85C, or derated voltage in series with a 3 resistor at 125C, capacitors shall meet the characteristic requirements in the table above. Endurance Capacitance Change ................ Refer to the table above (*1) Dissipation Factor ..................... Initial specified value or less Leakage Current ....................... Initial specified value or less After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its Shear Test sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified Terminal Strength jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 1% per 1000 hours at 85C, V with 0.1/V series impedance, R Failure Rate 60% confidence level. The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 89 040120