F93 Series Resin-Molded Chip, Standard Tantalum J-Lead TECHNICAL SPECIFICATIONS Item Performance Characteristics Category Temperature Range -55 to +125C (Rated temperature: +85C) Capacitance Tolerance 20%, 10% (at 120Hz) Dissipation Factor Refer to next page LEAD-FREE COMPATIBLE ESR (100kHz) Refer to next page COMPONENT After 1 minutes application of rated voltage, leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. After 1 minutes application of rated voltage, leakage current at 85C Leakage Current is not more than 0.1CV or 5A, whichever is greater. After 1 minutes application of derated voltage, leakage current at 125C is not more than 0.125CV or 6.3A, whichever is greater. FEATURES +15% Max. (at +125C) Capacitance Change +10% Max. (at +85C) by Temperature Compliant to the RoHS2 directive 2011/65/EU -10% Max. (at -55C) At 40C, 90 to 95% R.H., 500 hours (No voltage applied) SMD J-lead Damp Heat Capacitance Change ........... Refer to next page (*1) (Steady State) Dissipation Factor ................ Initial specified value or less Leakage Current.................. Initial specified value or less APPLICATIONS -55C / +125C 30 minutes each 5 cycles Low power DC/DC Capacitance Change ........... Refer to next page (*1) Temperature Cycles Dissipation Factor ................ Initial specified value or less Leakage Current.................. Initial specified value or less 10 seconds reflow at 260C, 5 seconds immersion at 260C. CASE DIMENSIONS: millimeters (inches) Resistance to Capacitance Change ........... Refer to next page (*1) Soldering Heat Dissipation Factor ................ Initial specified value or less Code L W W HS 1 2 Leakage Current.................. Initial specified value or less 3.20 0.20 1.60 0.20 1.20 0.10 1.60 0.20 0.80 0.20 A After application of surge voltage in series with a 33 resistor at the rate of (0.126 0.008) (0.063 0.008) (0.047 0.004) (0.063 0.008) (0.031 0.008) 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, 3.50 0.20 2.80 0.20 2.20 0.10 1.90 0.20 0.80 0.20 capacitors shall meet the characteristic requirements table below. Surge B Capacitance Change ........... Refer to next page (*1) (0.126 0.008) (0.110 0.008) (0.087 0.004) (0.075 0.008) (0.031 0.008) Dissipation Factor ................ Initial specified value or less 6.00 0.20 3.20 0.20 2.20 0.10 2.50 0.20 1.30 0.20 C Leakage Current.................. Initial specified value or less (0.236 0.008) (0.126 0.008) (0.087 0.004) (0.098 0.008) (0.051 0.008) After 2000 hours application of rated voltage in series with a 3 resistor at 7.30 0.20 4.30 0.20 2.40 0.10 2.80 0.20 1.30 0.20 85C, or derated voltage in series with a 3 resistor at 125C, capacitors N shall meet the characteristic requirements table below. (0.287 0.008) (0.169 0.008) (0.094 0.004) (0.110 0.008) (0.051 0.008) Endurance Capacitance Change ........... Refer to next page (*1) Dissipation Factor ................ Initial specified value or less A, B CASE C, N CASE Leakage Current.................. Initial specified value or less After applying the pressure load of 5N for 101 seconds horizontally to the center of capacitor side body which has no electrode and has been Shear Test soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the Terminal Strength center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable MARKING abnormality on the capacitor terminals. 1% per 1000 hours at 85C, VR with 0.1/V series impedance, A CASE B CASE C CASE N CASE Failure Rate 60% confidence level. Capacitance Capacitance Capacitance Capacitance We can supply the type of compliance to AEC-Q200. Please contact to your local Code (F) (F) (F) AVX sales office when these series are being designed in your application. 22 C 685 16V Rated Voltage Rated Voltage Rated Voltage Rated Voltage Code (V) (V) (V) 4V G 20V D 6.3V J 25V E 10V A 35V V 16V C HOW TO ORDER F93 1A 106 M A Type Rated Capacitance Tolerance Case Packaging Voltage Code Size K = 10% See page pF code: 1st two digits See M = 20% 168 for represent significant figures, table details 3rd digit represents multiplier above (number of zeros to follow) 14 JANUARY 2014 47 16V 100 16VF93 Series Resin-Molded Chip, Standard Tantalum J-Lead CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage F Code 4V (0G) 6.3V (0J) 10V (1A) 16V (1C) 20V (1D) 25V (1E) 35V (1V) 0.68 684 A 1 105 A A A 1.5 155 AA 2.2 225 A A A A/B 3.3 335 A A A B 4.7 475 A A/B A/B B/C 6.8 685 A A A/B C 10 106 A A A/B A/B B/C C 15 156 A A A/B C C N 22 226 A A A/B A/B/C B/C C/N N 33 336 A A A/B B/C C/N N 47 476 A A/B A/B/C B*/C/N C/N N 68 686 A A/B B/C N N* 100 107 A/B A/B/C B/C/N C/N 150 157 B B/C C/N N 220 227 A*/B/C B/C/N N N 330 337 C N N 470 447 N N 680 687 N Available Ratings Please contact to your local AVX sales office when these series are being designed in your application. *Codes under development subject to change JANUARY 2014 15