F98-AS1 Series Fused Tantalum Chip - Undertab F98-AS1 Series Fused Face-Down, High CV FEATURES Compliant to the RoHS3 directive 2015/863/EU SMD Face Down Design Small and Low Profile LEAD-FREE COMPATIBLE 100% Surge Current Tested COMPONENT APPLICATIONS Smartphone Mobile Phone Wireless Module Hearing Aid CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L W W H S S 1 2 1 2 +0.20 +0.20 2.00 -0.10 1.25 -0.10 0.900.10 0.800.10 0.500.10 1.000.10 S 0805 2012-09 +0.008 +0.008 (0.079 ) (0.049 ) (0.0350.004) (0.0310.004) (0.0200.004) (0.0390.004) -0.004 -0.004 MARKING L W1 H S CASE *Capacitance An Code W2 Rated Voltage S1 S2 S1 Code HOW TO ORDER F98 1A 336 M S AS1 Packaging Type Rated Capacitance Tolerance Case Fuse Series M = 20% Voltage Code Size Code Reel Dia Tape Width pF code: 1st two digits See (180) (mm) represent significant figures, table A 8 3rd digit represents multiplier above (number of zeros to follow) TECHNICAL SPECIFICATIONS Category Temperature Range: -55 to +125C Rated Temperature: +85C Capacitance Tolerance: 20% at 120Hz Dissipation Factor: Refer to next page ESR 100kHz: Refer to next page Refer to next page Provided that: After 5 minutes application of rated voltage, leakage current at 85C Leakage Current: 10 times or less than 20C specified value. After 5 minutes application of rated voltage, leakage current at 125C 12.5 times or less than 20C specified value. Termination Finish: Gold Plating (standard) The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 58 102020F98-AS1 Series Fused Face-Down, High CV CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage *Cap Code F Code 10V (1A) 16V (1C) 20V (1D) 25V (1E) 35 (1V) 1.0 105 S A 2.2 225 J 4.7 475 S 10 106 S a 22 226 S j 33 336 S n 47 476 S s Released ratings Please contact to your local AVX sales office when these series are being designed in your application. RATINGS & PART NUMBER REFERENCE 100kHz RMS Current (mA) Rated DF ESR *1 DCL AVX Case Capacitance Voltage 120Hz 100kHz C/C MSL (A) Part No. Size (F) 85C 125C 25C (V) (%) () (%) 10 Volt F981A226MSAAS1 S 22 10 2.2 20 4.5 100 90 40 20 3 F981A336MSAAS1 S 33 10 3.3 30 6.5 83 75 33 30 3 F981A476MSAAS1 S 47 10 9.4 35 5.5 90 81 36 30 3 16 Volt F981C106MSAAS1 S 10 16 1.6 18 4.5 100 90 40 20 3 35 Volt F981V105MSAAS1 S 1 35 0.7 20 8.5 73 65 29 30 3 *2: Leakage Current Moisture Sensitivity Level (MSL) is defined according to J-STD-020. After 5 minutes application of rated voltage, leakage current at 20C. QUALIFICATION TABLE F98-AS1 series (Temperature range -55C to +125C) TEST Condition At 40C, 90 to 95% R.H., 500 hours (No voltage applied) Damp Heat Capacitance Change ........... Refer to the table above (*1) (Steady State) Dissipation Factor ................ 150% or less of initial specified value Leakage Current ................... 200% or less of initial specified value -55C / +125C, 30 minutes each, 5 cycles Capacitance Change ........... Refer to the table above (*1) Temperature Cycles Dissipation Factor ................ 150% or less of initial specified value Leakage Current ................... 200% or less of initial specified value 10 seconds reflow at 260C, 5 seconds immersion at 260C. Resistance to Capacitance Change ........... Refer to the table above (*1) Dissipation Factor ................ Initial specified value or less Soldering Heat Leakage Current ................... Initial specified value or less After application of surge in series with a 1k resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, capacitors shall meet the characteristic requirements in the table above. Surge Capacitance Change ........... Refer the table above (*1) Dissipation Factor ................ 150% or less of initial specified value Leakage Current ................... 200% or less of initial specified value After 1000 hours application of rated voltage in series with a 3 resistor at 85C, capacitors shall meet the characteristic requirements in the table above. Endurance Capacitance Change .............Refer to the table above (*1) Dissipation Factor .................. 150% or less of initial specified value Leakage Current ....................200% or less of initial specified value After applying the pressure load of 5N for 101 seconds horizontally to the center of capacitor side bodywhich has no electrode and has been soldered beforehand on a substrate, there shall be found Shear Test neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength Terminal Strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. Fuse Activation 5 seconds max. with 2A min. applied current The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 59 063021