F98-AJ6 Series Resin-Molded Chip, High CV Facedown - Automotive Range F98-AJ6 Series Resin-Molded Chip, High CV Facedown - Automotive Range FEATURES Compliant to the RoHS3 directive 2015/863/EU SMD Face Down Design Small and Low Profile LEAD-FREE COMPATIBLE Compliant to AEC-Q200 COMPONENT 100% Surge Current Tested APPLICATIONS Infotainment Cabin Electronics Cameras Digital Millers CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L W W H S S 1 2 1 2 +0.20 +0.20 1.60 0.85 -0.10 -0.10 0.650.10 1.0 Max 0.500.10 0.600.10 +0.008 M 0603 1608-09 +0.008 (0.033 ) (0.063 -0.004 ) (0.0260.004) (0.039 Max) (0.0200.004) (0.0240.004) -0.004 +0.20 +0.20 2.00 -0.10 1.25 -0.10 0.900.10 0.800.10 0.500.10 1.000.10 0805 2012-09 +0.008 +0.008 S (0.079 ) (0.049 ) -0.004 -0.004 (0.0350.004) (0.0310.004) (0.0200.004) (0.0390.004) MARKING M CASE S CASE k k q q Date Date Code Code HOW TO ORDER F98 1C 106 M S AJ6 Type Rated Capacitance Code Tolerance Case Size Packaging AEC-Q200 pF code: 1st two digits M = 20% See table Voltage Compliant Code Reel Dia Tape Width Qty represent significant figures, above (mm) (mm) (pcs) 3rd digit represents multiplier A 4000 (number of zeros to follow) 180 8 U 1000 TECHNICAL SPECIFICATIONS Category Temperature Range: -55 to +125C Rated Temperature: +85C Capacitance Tolerance: 20% at 120Hz Dissipation Factor: Refer to Ratings & Part Number Reference ESR 100kHz: Refer to Ratings & Part Number Reference Refer to Ratings & Part Number Reference at 20C after application of rated voltage for 5 minutes Provided that: After 5 minutes application of rated voltage, leakage current at 85C Leakage Current: 10 times or less than 20C specified value. After 5 minutes application of rated voltage, leakage current at 125C 12.5 times or less than 20C specified value. Termination Finish: Gold Plating (standard) The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 61 102020F98-AJ6 Series Resin-Molded Chip, High CV Facedown Automotive Range CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage Cap F Code 6.3 (0J) 10V (1A) 16V (1C) Code 4.7 475 M M S 10 106 M S a 22 226 M* S* j 33 336 M* n 47 476 S* s Released Ratings * Codes under development - subject to change RATINGS & PART NUMBER REFERENCE 100kHz RMS Current Rated DCL DF ESR Case Cap (mA) AVX Part Number Voltage Max Max Max C/C MSL Size ( F ) (V) ( A) (% 120Hz) ( 10 0 k Hz) 25C 85C 125C 10 Volt F981A475MMAAJ6 M 4.7 10 0.5 12 6 65 58 26 30 3 F981A106MMAAJ6 M 10 10 1.0 20 7.5 58 52 23 30 3 16 Volt F981C475MMAAJ6 M 4.7 16 0.8 12 12 46 41 18 30 3 F981C106MSAAJ6 S 10 16 1.6 18 4 106 95 42 30 3 QUALIFICATION TABLE F98-AJ6 series (Temperature range -55C to +125C) Test Condition At 40C, 90% R.H., 500 hours (No voltage applied) Damp Heat Capacitance Change............Refer to Ratings & Part Number Reference (Steady State) Dissipation Factor................150% or less of initial specified value Leakage Current...................200% or less of initial specified value After 1000 hour s application of rated voltage in series with a 33 resistor at 85C, 85% R.H., capacitors meet the characteristics requirements table below. Capacitance Change............Refer to Ratings & Part Number Reference Load Humidity Dissipation Factor................150% or less of initial specified value Leakage Current...................10 times or less of initial specified value At -55C / +125C, 30 minutes each, 1000 cycles Temperature Capacitance Change............Refer to Ratings & Part Number Reference Cycles Dissipation Factor................150% or less initial specified value Leakage Current...................5 times or less of initial specified value 10 seconds reflow at 260C, 5 seconds immersion at 260C Resistance to Capacitance Change............Refer to Ratings & Part Number Reference Soldering Heat Dissipation Factor................Initial specified value or less Leakage Current...................Initial specified value or less After application of surge voltage in series with a 1k resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change............Refer to Ratings & Part Number Reference Surge Dissipation Factor................150% or less of initial specified value Leakage Current...................200% or less of initial specified value After 1000 hours application of rated voltage in series with a 3 resistor at 85C, or derated voltage in series with a 3 resistor at 125C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change............Refer to Ratings & Part Number Reference Endurance Dissipation Factor................150% or less of initial specified value Leakage Current...................200% or less of initial specified value After applying the pressure load of 5N for 60+1/-0 seconds horizontally to the center of capacitor side body Shear Test which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both Terminal of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied Strength with a specified jig at the center of substrate so that he substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 62 063021