F9H Series High Temperature (150C max.) - J-Lead F9H Series High Temperature 150C, Improved Reliability J-Lead FEATURES Compliant to the RoHS3 directive 2015/863/EU Compliant to AEC-Q200 Improved Reliability - FR=0.5%/1000hrs LEAD-FREE COMPATIBLE 100% Surge Current Tested COMPONENT SMD J-lead APPLICATIONS Automotive Electronics (Engine ECU, Transmission ECU, ISG, Head Lamp) Industrial Equipment CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L W W H S 1 2 3.20 0.20 1.60 0.20 1.20 0.10 1.60 0.20 0.80 0.20 A 1206 3216-18 (0.126 0.008) (0.063 0.008) (0.047 0.004) (0.063 0.008) (0.031 0.008) 3.50 0.20 2.80 0.20 2.20 0.10 1.90 0.20 0.80 0.20 B 1210 3528-21 (0.138 0.008) (0.110 0.008) (0.087 0.004) (0.075 0.008) (0.031 0.008) 6.00 0.20 3.20 0.20 2.20 0.10 2.50 0.20 1.30 0.20 C 2312 6032-27 (0.236 0.008) (0.126 0.008) (0.087 0.004) (0.098 0.008) (0.051 0.008) A, B CASE C CASE MARKING L W1 L W1 A CASE B CASE C CASE Capacitance Capacitance Capacitance H H (F) (F) Code Month Code 22 Month C 160 W2 W2 Code 16r S S S S Rated Voltage Rated Voltage Rated Voltage (V) (V) Code HOW TO ORDER F9H 1C 106 M A Type Rated Capacitance Tolerance Case Packaging K = 10% See Tape & Reel Voltage Code Size M = 20% Packaging Section pF code: 1st two digits See represent significant figures, table 3rd digit represents multiplier above (number of zeros to follow) TECHNICAL SPECIFICATIONS Category Temperature Range: -55 to +150C Rated Temperature: +105C Capacitance Tolerance: 20%, 10% at 120Hz Dissipation Factor: Refer to next page ESR 100kHz: Refer to next page Leakage Current: After 1 minutes application of rated voltage, leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. After 1 minutes application of rated voltage, leakage current at 105C is not more than 0.1CV or 5A, whichever is greater. After 1 minutes application of derated voltage, leakage current at 150C is not more than 0.125CV or 6.3A, whichever is greater. Capacitance Change By Temperature +15% Max. at +150C +10% Max. at +105C -10% Max. at -55C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or 120 available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 102220 47 16rF9H Series High Temperature 150C, Improved Reliability J-Lead Voltage vs Temperature Rating CAPACITANCE AND RATED VOLTAGE RANGE 100% 100% 100% 90% (LETTER DENOTES CASE SIZE) 80% 70% 67% 67% Capacitance Rated Voltage 60% 63% 50% F Code 10V (1A) 16V (1C) Released ratings 50% 50% 42% 40% Please contact to your local AVX sales 30% 10 106 A 32% 20% office when these series are being 15 156 A 10% designed in your application. 0% 22 226 B -55C 105C 150C 33 336 Rated Voltage Recommended Applications Voltage in General Circuit Recommended Applications Voltage in Low Impedance Circuit 47 476 C RATINGS & PART NUMBER REFERENCE Rated Leakage DF ESR *1 100kHz RMS Current (mA) AVX Case Capacitance Voltage Current 120Hz 100kHz C/C MSL Part No. Size (F) (V) (A) (%) () 25C 105C 150C (%) 10 Volt F9H1A156 AA A 15 10 1.5 10 3.0 158 142 63 * 3 16 Volt F9H1C106 AA A 10 16 1.6 8 3.5 146 132 59 * 3 F9H1C226 BA B 22 16 3.5 8 1.9 212 190 85 * 3 F9H1C476 CC C 47 16 7.5 10 1.1 316 285 126 * 3 *1: C/C Marked * : for 20% tolerance, for 10% tolerance. Moisture Sensitivity Level (MSL) is defined according to J-STD-020. Item All Case (%) Damp Heat 10 Temperature cycles 5 Resistance soldering heat 5 Surge 5 Endurance 10 Load Humidity 10 QUALIFICATION TABLE F9H series (Temperature range -55C to +150C) TEST Condition At 85C, 85% R.H., 1000 hours (No voltage applied) Damp Heat Capacitance Change .................Refer to page 118 (*1) Dissipation Factor ....................... Initial specified value or less (Steady State) Leakage Current .......................... 125% or less than the initial specified value After 1000 hours application of rated voltage in series with a 33 resistor at 85C, 85% R.H., capacitors meet the characteristics requirements table below. Load Humidity Capacitance Change .................Refer to page 118 (*1) Dissipation Factor ....................... 120% or less than the initial specified value Leakage Current .......................... 200% of less than the initial specified value At -55C / +150C, 30 minutes each, 1000 cycles Capacitance Change .................Refer to page 118 (*1) Temperature Cycles Dissipation Factor ....................... Initial specified value or less Leakage Current .......................... Initial specified value or less 10 seconds reflow at 260C, 5 seconds immersion at 260C. Resistance to Capacitance Change .................Refer to page 118 (*1) Dissipation Factor ....................... Initial specified value or less Soldering Heat Leakage Current .......................... Initial specified value or less After immersing capacitors completely into a solder pot at 245C for 2 to 3 seconds, Solderability more than 3/4 of their electrode area shall remain covered with new solder. After application of surge voltage in series with a 33 resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change Surge Refer to page 118 (*1) Dissipation Factor ..........................Initial specified value or less Leakage Current .............................Initial specified value or less After 2000 hours application of rated voltage in series with a 3 resistor at 105C, or derated voltage in series with a 3 resistor at 150C, capacitors shall meet the characteristic requirements in the table above. Endurance Capacitance Change ...................... Refer to page 118 (*1) Dissipation Factor ............................ Initial specified value or less Leakage Current ............................... Initial specified value or less After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body Shear Test which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode.. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a Terminal Strength specified jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 0.5% per 1000 hours at 105C, V with 0.1/V series impedance, R Failure Rate 60% confidence level. The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or 121 available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 040220