MLCC Tin/Lead Termination B
C0G (NP0) General Specifications
AVX Corporation will support those customers for
commercial and military Multilayer Ceramic Capacitors with
a termination consisting of 5% minimum lead. This
termination is indicated by the use of a B in the 12th
position of the AVX Catalog Part Number. This fulfills AVXs
commitment to providing a full range of products to our
customers. AVX has provided in the following pages a full
range of values that we are currently offering in this special
B termination. Please contact the factory if you require
additional information on our MLCC Tin/Lead Termination
B products.
Not RoHS Compliant
PART NUMBER (see page 2 for complete part number explanation)
LD05 A 101 J A B
5 2 A
Size Dielectric Capacitance Capacitance Failure Terminations
Voltage Packaging Special
LD02 - 0402 C0G (NP0) = A Code (In pF) Tolerance Rate
6.3V = 6 B = 5% min lead 2 = 7" Reel Code
LD03 - 0603 X7R = C B = .10 pF (<10pF) A = Not
10V = Z 2 Sig. Digits + 4 = 13" Reel A = Std.
X = FLEXITERM
LD04 - 0504* X5R = D C = .25 pF (<10pF) Applicable
16V = Y Product
Number of
with 5% min
LD05 - 0805 X8R = F D = .50 pF (<10pF)
25V = 3 Contact Factory
Zeros
lead**
LD06 - 1206 F = 1% ( 10 pF)
35V = D For
LD10 - 1210 G = 2% ( 10 pF)
50V = 5 Multiples
**X7R only
LD12 - 1812 J = 5%
100V = 1
LD13 - 1825 K = 10%
200V = 2
LD14 - 2225 M = 20%
500V = 7
LD20 - 2220
See FLEXITERM section for CV options
*LD04 has the same CV ranges as LD03.
NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers.
Contact factory for non-specified capacitance values.
Insulation Resistance vs Temperature
10,000
1,000
100
0
0 20 40 60 80 100
Temperature C
112916
40
Insulation Resistance (Ohm-Farads)MLCC Tin/Lead Termination B
C0G (NP0) Specifications and Test Methods
Parameter/Test NP0 Specification Limits Measuring Conditions
Operating Temperature Range -55C to +125C Temperature Cycle Chamber
Capacitance Within specified tolerance Freq.: 1.0 MHz 10% for cap 1000 pF
<30 pF: Q 400+20 x Cap Value 1.0 kHz 10% for cap > 1000 pF
Q
30 pF: Q 1000 Voltage: 1.0Vrms .2V
100,000M or 1000M - F, Charge device with rated voltage for
Insulation Resistance
whichever is less 60 5 secs @ room temp/humidity
Charge device with 250% of rated voltage for
Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current
limited to 50 mA (max)
Note: Charge device with 150% of rated
voltage for 500V devices.
Appearance No defects Deflection: 2mm
Capacitance Test Time: 30 seconds
5% or .5 pF, whichever is greater
Resistance to Variation
Flexure
Q Meets Initial Values (As Above)
Stresses
Insulation
Initial Value x 0.3
Resistance
95% of each terminal should be covered Dip device in eutectic solder at 230 5C
Solderability
with fresh solder for 5.0 0.5 seconds
Appearance No defects, <25% leaching of either end terminal
Capacitance
2.5% or .25 pF, whichever is greater
Variation
Dip device in eutectic solder at 260C for 60
seconds. Store at room temperature for 24 2
Resistance to Q Meets Initial Values (As Above)
Solder Heat hours before measuring electrical properties.
Insulation
Meets Initial Values (As Above)
Resistance
Dielectric
Meets Initial Values (As Above)
Strength
Appearance No visual defects Step 1: -55C 2 30 3 minutes
Capacitance
2.5% or .25 pF, whichever is greater Step 2: Room Temp 3 minutes
Variation
Thermal
Q Meets Initial Values (As Above) Step 3: +125C 2 30 3 minutes
Shock
Insulation
Meets Initial Values (As Above) Step 4: Room Temp 3 minutes
Resistance
Dielectric Repeat for 5 cycles and measure after
Meets Initial Values (As Above)
Strength 24 hours at room temperature
Appearance No visual defects
Capacitance
3.0% or .3 pF, whichever is greater
Variation Charge device with twice rated voltage in
30 pF: Q 350 test chamber set at 125C 2C
Q
Load Life 10 pF, <30 pF: Q 275 +5C/2 for 1000 hours (+48, -0).
(C=Nominal Cap)
<10 pF: Q 200 +10C
Insulation Remove from test chamber and stabilize at
Initial Value x 0.3 (See Above)
Resistance room temperature for 24 hours
Dielectric before measuring.
Meets Initial Values (As Above)
Strength
Appearance No visual defects
Capacitance
5.0% or .5 pF, whichever is greater
Variation Store in a test chamber set at 85C 2C/
30 pF: Q 350 85% 5% relative humidity for 1000 hours
Load Q 10 pF, <30 pF: Q 275 +5C/2 (+48, -0) with rated voltage applied.
Humidity <10 pF: Q 200 +10C
Insulation Remove from chamber and stabilize at
Initial Value x 0.3 (See Above)
Resistance room temperature for 24 2 hours
Dielectric before measuring.
Meets Initial Values (As Above)
Strength
112916
41