SA13A Littelfuse

TVS Diodes Axial Leaded 500W > SA series Pb e3 RoHS SA Series Description Bi-directional The SA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional 500W peak pulse EFT protection of dat a capability at 10/1000s lines in accordance with waveform, repetition rate IEC 61000-4-4 (duty cycles):0.01% Low incremental surge V T = V 25C resistance BR J BR Agency Approvals x (1+T x (T - 25)) Typical I less than 1A J R (T:Temperature when V max>13V BR Agency Agency File Number Coefficient, typical value High temperature is 0.1%) E230531 to reflow soldering Glass passivated chip guaranteed: 260C/40sec junction in DO-15 Package / 0.375,(9.5mm) lead Maximum Ratings and Thermal Characteristics Fast response time: length, 5 lbs., (2.3kg) O (T =25 C unless otherwise noted) typically less than 1.0ps tension A from 0 Volts to BV min Plastic package is Parameter Symbol Value Unit Excellent clamping ammabilitfl y rated V-0 per capability Underwriters Laboratories Peak Pulse Power Dissipation by 10/1000s Test P 500 W PPM Waveform (Fig.2)(Note 1) Typical failure mode is Matte tin leadfree plated Steady State Power Dissipation on Infinite Heat short from over-specified P 3.0 W Halogen free and RoHS D Sink at T =75C L voltage or current compliant Peak Forward Surge Current, 8.3ms Single Half I 70 A FSM Whisker test is conducted Sine Wave Unidirectional Only (Note 2) Pb-free E3 means 2nd based on JEDEC Maximum Instantaneous Forward Voltage at 35A level interconnect is Pb- V 3.5 V F for Unidirectional Only JESD201A per its table 4a free and the terminal finish Operating Junction and Storage Temperature -65 to and 4c material is tin(Sn) (IPC/ T , T C J STG Range 175 IEC-61000-4-2 ESD JEDEC J-STD-609A.01) Typical Thermal Resistance Junction to Lead R 20 C/W JL 30kV(Air), 30kV (Contact) Typical Thermal Resistance Junction to Ambient R 75 C/W JA ESD protection of dat a Notes: lines in accordance with O 1. Non-repetitive current pulse , per Fig. 4 and derated above T (initial) =25 C per Fig. 3. J IEC 61000-4-2 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. Applications TVS devices are ideal for the protection of I/O interfaces, V bus and other vulnerable circuits used in telecom, CC computer, industrial and consumer electronic applications. Functional Diagram Additional Infomarion Datasheet Resources Samples Bi-directional Cathode Anode Uni-directional 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20TVS Diodes Axial Leaded 500W > SA series Electrical Characteristics (T =25C unless otherwise noted) A Maximum Maximum Reverse Agency Test Maximum Breakdown Voltage V Clamping Part Part BR Current Peak Pulse Approval Stand off Reverse Voltage (Volts) I Number Number T I Leakage I V Voltage T Current I R R V I (Uni) (Bi) pp C PP (A) (mA) V (V) R (A) Min. Max. (V) SA5.0A SA5.0CA 5.0 6.40 7.00 10 9.2 55.4 600 X SA6.0A SA6.0CA 6.0 6.67 7.37 10 10.3 49.5 600 X SA6.5A SA6.5CA 6.5 7.22 7.98 10 11.2 45.5 400 X SA7.0A SA7.0CA 7.0 7.78 8.60 10 12.0 42.5 150 X SA7.5A SA7.5CA 7.5 8.33 9.21 1 12.9 39.5 50 X SA8.0A SA8.0CA 8.0 8.89 9.83 1 13.6 37.5 25 X SA8.5A SA8.5CA 8.5 9.44 10.40 1 14.4 35.4 10 X SA9.0A SA9.0CA 9.0 10.00 11.10 1 15.4 33.1 5 X SA10A SA10CA 10.0 11.10 12.30 1 17.0 30.0 3 X SA11A SA11CA 11.0 12.20 13.50 1 18.2 28.0 1 X SA12A SA12CA 12.0 13.30 14.70 1 19.9 25.6 1 X SA13A SA13CA 13.0 14.40 15.90 1 21.5 23.7 1 X SA14A SA14CA 14.0 15.60 17.20 1 23.2 22.0 1 X SA15A SA15CA 15.0 16.70 18.50 1 24.4 20.9 1 X SA16A SA16CA 16.0 17.80 19.70 1 26.0 19.6 1 X SA17A SA17CA 17.0 18.90 20.90 1 27.6 18.5 1 X SA18A SA18CA 18.0 20.00 22.10 1 29.2 17.5 1 X SA20A SA20CA 20.0 22.20 24.50 1 32.4 15.7 1 X SA22A SA22CA 22.0 24.40 26.90 1 35.5 14.4 1 X SA24A SA24CA 24.0 26.70 29.50 1 38.9 13.1 1 X SA26A SA26CA 26.0 28.90 31.90 1 42.1 12.1 1 X SA28A SA28CA 28.0 31.10 34.40 1 45.4 11.2 1 X SA30A SA30CA 30.0 33.30 36.80 1 48.4 10.5 1 X SA33A SA33CA 33.0 36.70 40.60 1 53.3 9.6 1 X SA36A SA36CA 36.0 40.00 44.20 1 58.1 8.8 1 X SA40A SA40CA 40.0 44.40 49.10 1 64.5 7.9 1 X SA43A SA43CA 43.0 47.80 52.80 1 69.4 7.3 1 X SA45A SA45CA 45.0 50.00 55.30 1 72.7 7.0 1 X SA48A SA48CA 48.0 53.30 58.90 1 77.4 6.6 1 X SA51A SA51CA 51.0 56.70 62.70 1 82.4 6.2 1 X SA54A SA54CA 54.0 60.00 66.30 1 87.1 5.9 1 X SA58A SA58CA 58.0 64.40 71.20 1 93.6 5.4 1 X SA60A SA60CA 60.0 66.70 73.70 1 96.8 5.3 1 X SA64A SA64CA 64.0 71.10 78.60 1 103.0 5.0 1 X SA70A SA70CA 70.0 77.80 86.00 1 113.0 4.5 1 X SA75A SA75CA 75.0 83.30 92.10 1 121.0 4.2 1 X SA78A SA78CA 78.0 86.70 95.80 1 126.0 4.0 1 X SA85A SA85CA 85.0 94.40 104.00 1 137.0 3.7 1 X SA90A SA90CA 90.0 100.00 111.00 1 146.0 3.5 1 X SA100A SA100CA 100.0 111.00 123.00 1 162.0 3.1 1 X SA110A SA110CA 110.0 122.00 135.00 1 177.0 2.9 1 X SA120A SA120CA 120.0 133.00 147.00 1 193.0 2.6 1 X SA130A SA130CA 130.0 144.00 159.00 1 209.0 2.4 1 X SA150A SA150CA 150.0 167.00 185.00 1 243.0 2.1 1 X SA160A SA160CA 160.0 178.00 197.00 1 259.0 2.0 1 X SA170A SA170CA 170.0 189.00 209.00 1 275.0 1.9 1 X SA180A SA180CA 180.0 200.00 221.00 1 289.0 1.7 1 X For bidirectional type having V of 10 volts and less, the I limit is double. R R For parts without A , the V is 10% and Vc is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. BR 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20