10.11mm LM930 Bluetooth low energy Module (with IPEX Connector) Product LM930 Part No See Last Page Standalone (With Embedded Bluetooth v4.1 Stack) Revised 25/AUG/2017 Features Bluetooth v4.1 specication I C and UART 14 mA Current Consumption (at 0 dBm Tx Output Power) 9 digital and 3 analogue I/O (10-bit ADC) IPEX Connector Wake-up interrupt and Watchdog timer 9 dBm Tx Output Power (Max) and -92 dBm Rx Sensitivity 4 PWM channels Over-the-Air Upgrade (OTAU) available 22mm x 10.11mm x 2.50mm Application Firmware Support SMT Side and Bottom Pads for easy production See our website for this products certications IoT Applications available including Serial over GATT, Eddystone Beacon and Cloud Sensor & Cloud Collector RoHS, REACH and WEEE Compliant Solution Fully integrated module with no additional components required Overview The LM930 Bluetooth low energy module is designed for use within embedded systems. It is implemented as a peripheral device within a product, while saving the developer valuable PCB space. The LM930 enables wireless communication with other nearby Bluetooth low energy devices (e.g. iOS and Android) using a highly power e cient connection. The transmission output power ranges from 0 dBm to 9 dBm and can be congured to provide an extended battery life or a longer communication range. This single core standalone module combines a Bluetooth low energy radio using a Bluetooth v4.1 stack, plus a microcontroller with 512 kB EEPROM for running the application. The LM930 incorporates 27 pin outs including UART and I C for interfacing with a wide range of peripheral devices like sensors. Its SMT side and bottom pads allow for easy manufacture and placement into your product. Application rmware and conguration settings can be preloaded to the module before supply. LM o er bespoke integration into your product by supporting your developer. We can also assist in the development of new IoT applications for the module. IoT applications such as Serial over GATT, iBeacon and Key Fob (with RGB LED Controller) are available with the modules LM53X development kits. The rmware is customisable to meet your requirements. The IPEX connector provides the developer with the exibility to add an antenna that suits the products unique requirements, such as dipole, IC or PCB antenna types. The selected antenna can be placed anywhere on the product, which is useful for avoiding any metallic surfaces of the product housing and a noisy environment of the products PCB. Depending on the antenna used a longer range, omnidirectional or unidirectional RF signal is produced. LM930 +44(0) 207 428 2647 sales lm-technologies.com Page 1 of 14 2.50mm 22mmProduct LM930 LM930 Bluetooth low energy Module (with IPEX Connector) Part No See Last Page Standalone (With Embedded Bluetooth v4.1 Stack) General Specication Wireless v4.1 Bluetooth Standard Standalone (Embedded Bluetooth Stack) Module Type GATT-Based Proles Hardware Qualcomm Chipset IPEX Connector Antenna 16-bit RISC Microcontroller (MCU) 512 kB EEPROM Memory 64 kB RAM SPI Programming Interface I C, UART, AIO and PIO Interfaces 3V3 (3V6 Max) Power Supply 32 kHz and 16 MHz Crystal Oscillators LM53X Development Kit RF Characteristics 0 dBm to 9 dBm Tx Output Power -92 dBm (Typical) Rx Sensitivity 14 mA (at 0 dBm), 15.9 mA (at 3 dBm) and <25 mA (at 9 dBm) Current Consumption (Cont.Tx) 22 mA (Typical) Current Consumption (Cont.Rx) 110m + (with a 2 dBi antenna) Range (in open space) Up to 1 Mbps Data Rate 2.4 GHz to 2.485 GHz Frequency Physical Characteristics Operating Temperature -30C to +85C Dimensions (L x W x H) 22mm x 10.11mm x 2.50mm Weight 0.82g Certications See our website for this products certications Compliance RoHS, REACH and WEEE Compliant Solution LM930 +44(0) 207 428 2647 sales lm-technologies.com Page 2 of 14