LioN-Power Multi-protocol 8 Digital Inputs / 8 Digital Outputs, M12 L-coded or 7/8 Power Supply Connection, PROFINET, EtherNet/IP or EtherCAT Product Description Type 0980 ESL 393-121 0980 ESL 393-111 NEW NEW Description LioN-P Multi-protocol module, PROFINET, EtherNet/IP or EtherCAT de- LioN-P Multi-protocol module, PROFINET, EtherNet/IP or EtherCAT de- vice, 8 digital input and 8 digital output channels with galvanic isolation vice, 8 digital input and 8 digital output channels with galvanic isolation, M12 LAN connection, 4-poles, D-coded, M12 L-coded M12 LAN connection, 4-poles, D-coded, 7/8 power supply, 5-poles power supply, 5-poles Order No. 934879003 934882003 Technical Data Protection Degree IP65, IP67, IP69K (only if mounted and locked in combination IP65, IP67 (only if mounted and locked in combination with Hirschmann/Lumberg connector) with Hirschmann/Lumberg connector) Ambient Temperature (Operation) -20 C to +70 C Dimensions (W x H x D) 59.6 x 30.7 x 200 (mm) 59.6 x 26.2 x 206 (mm) Weight 500 g 520 g Housing Material Metal, Zinc Die-cast Bus System Protocol PROFINET /EtherNet/IP/EtherCAT I/O Device Connection M12 LAN connection, 4-poles, D-coded Transmission Rate Fast Ethernet (10/100 Mbit/s), Full Duplex Rotary Address Switches Yes, 3x Power Supply Nominal Voltage 24 V DC (SELV/PELV) Nominal Voltage Range 18 to 30 V DC Connection M12, L-coded, 5-poles 7/8 , 5-poles Current Carrying Capacity of Connector 16 A 9 A Current Consumption (typ.) 160 mA (+/-20% at 24 V DC) Input Channels Number of Channels 8 Connection M12, 5-poles, A-coded Channel Type Type 3 acc. to IEC 61131-2 Nominal Voltage 24 V DC via US (system power supply) Sensor Current Supply 200 mA per Port Sensor Type PNP Output Channels Number of Channels 8 Connection M12, 5-poles, A-coded Channel Type p-switching Nominal Voltage 24 V DC via Uaux (actuator power supply) Output Current per Channel max. 2 A Output Current per Module max. 9 A Protective Circuit Electronicaly: Overload protection, short-circuit protection Galvanically Isolated Yes Continued Next Page Bit Assignment Bit 7 6 5 4 3 2 1 0 M12 Input 8DI Byte 0 4B 4A 3B 3A 2B 2A 1B 1A M12 Output 8DO Byte 1 8B 8A 7B 7A 6B 6A 5B 5A Data Sheet: 0980 ESL 393-121 111 www.lumberg-automationusa.com 1.800.Belden1 www.lumberg-automationusa.comLioN-Power Multi-protocol 8 Digital Inputs / 8 Digital Outputs, M12 L-coded or 7/8 Power Supply Connection, PROFINET, EtherNet/IP or EtherCAT Diagnostic Indication 0980 ESL 393-121 and 0980 ESL 393-111 LED Indicator Condition 1...8 A Yellow Channel status 1...8 DIA A Red Periphery error 1...8 B White Channel status 1...8 DIA B Red Periphery error P1 Lnk/Act Green Connection to an Ethernet device Green blinking I/O device exchanging data Off No connection to another device P2 Lnk/Act Green Connection to an Ethernet device Yellow blinking I/O device exchanging data Off No connection to another device PROFINET BF Red Bus error, no data exchange with I/O controller Off No error message DIA Red Common indicator for periphery errors Red blinking Firmware update Off No error message EtherNet/IP MS (Module status) Green Device is ready for operating Green blinking Wrong configuration Red/green blinking Self test is running Red blinking Firmware update Off IP address is available NS (Network status) Green blinking IP address is available Green Connection to master is available Red blinking At least one connection has timed out Red IP address is already being used by another device Red/green blinking Self test is running Off Device is switched off/device has no IP address EtherCAT RUN Green Device is in state OPERATIONAL Green blinking Device is in state PRE-OPERATIONAL Green single flash Device is in state SAFE-OPERATIONAL Green flickerng Device is in state BOOTSTRAP Off Device is in state INIT ERR RedAn critical communication or application controller error has occurred Red double flash An application watchdog timeout has occurred. Red single flashSlave device application has changed the EtherCAT state autonomously, due to local erro Red blinking General Configuration Error Red flickering Booting Error was detected Off No error US Green Voltage 19 V <= US <= 30 V Red US Voltage < 19 V or US > 30 V UL Green Voltage 19 V <= UL <= 30 V Red UL Voltage < 19 V or UL > 30 V Pin Assignment M12 I/O Port, M12 Power Supply, M12 LAN Connection, Power Supply 7/8 A-coded L-coded D-coded 1 = +24 V 1 = +24 V 1 = GND UL 1 = TD+ 2 = IN B 2 = GND UL 2 = GND (0 V) 2 = RD+ 3 = GND (0 V) 3 = GND (0 V) 3 = FE 3 = TD- 4 = IN A 4 = +24 V UL 4 = +24 V 4 = RD- 5 = FE 5 = FE 5 = +24 V UL Continued Next Page www.lumberg-automationusa.com Data Sheet: 0980 ESL 393-121 111 1.800.Belden1 www.lumberg-automationusa.com