SP510E ULTRA HIGH SPEED MULTIPROTOCOL TRANSCEIVER JANUARY 2020 REV. 1.0.2 FEATURES GENERAL DESCRIPTION Up to 52Mbps Differential Transmission Rates The SP510E is a highly integrated physical layer solution that is configurable to support multiple serial 15kV HBM ESD Tolerance for Analog I/O Pins standards. It incorporates eight drivers and eight Integrated Termination Resistors for V.11/V.35 receivers (8TX/8RX), configurable for either Eight Drivers and Eight Receivers (8TX/8RX) differential (V.11 or V.35) or single ended (V.28 and Adjustable Logic Level Pin V (Down to 1.65V) V.10) signaling. L Software Selectable Protocols with 3-Bit Word: SP510E enables a Serial Communications Controller to implement a variety of serial port types including - RS-232 (V.28) V.24, V.25, V.36, EIA-530, EIA-530-A, X.21, RS-232. - EIA-530 (V.10 & V.11) The device architecture is designed to support the - EIA-530A (V.10 & V.11) data and clock signals used in HDLC or SDLC serial - X.21 (V.11) ports as either DTE or DCE. - RS-449/V.36 Operating configuration is programmable in system Internal Line or Digital Loopback Testing using the mode-select pins. The V.11 and V.35 modes Adheres to NET1/NET2 and TBR2 Requirements include internal bus termination that may be switched Easy Flow-Through Pinout in or out using the TERM OFF pin. Single +5V Supply Voltage The SP510E is ideal for space constrained Individual Driver/Receiver Enable/Disable Controls applications. It requires only a single 5V supply for full operation. The V pin determines the receiver output L Operates in DTE or DCE Mode voltage (V , down to 1.65V), for interfacing with OH Pin Compatible Upgrade for SP509, SP508 lower voltage CPUs and FPGAs. For single supply operation at 5V the V pin will be connected to V . L CC Fully compliant V.28 and V.10 driver output voltages TYPICAL APPLICATIONS are generated using the onboard charge pump. Special power sequencing is not required during Data Communication Networks system startup. Charge pump outputs are internally Telecommunication Equipment regulated to minimize power consumption. The Secured Data Communication SP510E requires only four 1F capacitors for complete functionality. The device may be put into a CSU and DSU low power shutdown mode when not in active use. Data Routers All receivers have fail-safe protection to put outputs Network Switches into an output-high state when inputs are open, WAN Access Equipment shorted, or terminated but idle. VoIP-PBX Gateways (1) ORDERING INFORMATION (2) PART NUMBER OPERATING TEMPERATURE RANGE PACKAGE PACKAGING METHOD LEAD-FREE SP510EEF-L -40C to +85C 100-pin LQFP Tray Yes SP510ECF-L 0C to +70C 100-pin LQFP Tray Yes NOTES: 1. Refer to SP510E ULTRA HIGH SPEED MULTIPROTOCOL TRANSCEIVER REV. 1.0.2 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Supply Voltage V +7.0V CC Logic-Interface Voltage (V ) V V L L CC Receiver DC Input Voltage 15.5V -0.3V to (V + 0.5V) Input Voltage at TTL Input Pins CC Driver Output Voltage (from Ground) -7.5V to +12.5V Short Circuit Duration, TxOUT to GND Continuous Storage Temperature Range -65C to +150C Lead Temperature (soldering, 10s) +300C Continuous Power Dissipation at T = +70C AMB 100-Pin LQFP 1520mW (derate 19mW/C above +70C) = 52.7C/W, = 6.5C/W JA JC ESD PROTECTION TX Output & RX Input Pins 15 kV Human Body Model All Other Pins 2 kV Human Body Model 2