100W Constant Voltage + Constant Current LED Driver ELG-100 series IP65 IP67 *& / 6 , A & 7> 0 C + = 0 , B( .) 789 + 78. > D E , F - ,, ,& & F =, , ,, F * , G.(((( . 0 %& (( (() * + , %& (( , ((-(./* , 0 0 1/ .1/ 2 3 4 0 &1( 5 63( , , 789+ 78. 0 %& (( : 0 ,, , , , > , 1+-8+1 +1<+.1/ 0 = , 7 > C A 2 789 / = 2 A 78. / E & , = 2 A 789 - ,, (5 (/ (/ 7) = 2 * 789 * = 2 Dx 789 A & =, , ,, : A : 789 A & =, , ,, ,, = 2 File Name:ELG-100-SPEC 2016-08-30100W Constant Voltage + Constant Current LED Driver ELG-100 series SPECIFICATION MODEL ELG-100-24 ELG-100-36 ELG-100-42 ELG-100-48 ELG-100-54 24V 42V 48V 54V DC VOLTAGE 36V CONSTANT CURRENT REGION Note.2 12 ~ 24V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT 4.0A 2.66A 2.28A 2A 1.78A 96W 95.76W 96W 96.12W RATED POWER 95.76W RIPPLE & NOISE (max.) Note.3 200mVp-p 250mVp-p 250mVp-p 300mVp-p 350mVp-p Adjustable for A-Type only (via the built-in potentiometer) VOLTAGE ADJ. RANGE 21.6 ~ 26.4V 32.4 ~ 39.6V 43.2 ~ 52.8V 48.6 ~ 59.4V 37.8 ~ 46.2V OUTPUT Adjustable for A-Type only (via the built-in potentiometer) CURRENT ADJ. RANGE 2 ~ 4A 1.33 ~ 2.66A 1.14 ~ 2.28A 1 ~ 2A 0.89 ~ 1.78A VOLTAGE TOLERANCE Note.4 3.0% 2.5% 2.5% 2.0% 2.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 0.5% 0.5% 0.5% LOAD REGULATION SETUP, RISE TIME Note.6 1000ms, 80ms/115VAC 500ms, 100ms/230VAC 15ms/115VAC 10ms/230VAC HOLD UP TIME (Typ.) 100 ~ 305VAC 142 ~ 431VDC VOLTAGE RANGE Note.5 (Please refer toSTATIC CHARACTERISTI section) FREQUENCY RANGE 47 ~ 63Hz PF0.97/115VAC, PF 0.95/230VAC, PF0.92/277VAC full load POWER FACTOR (Please refer toPOWER FACTOR (PF) CHARACTERISTI section) THD< 20%( load50%/115VC load 60%/230VAC load75%/277VAC) TOTAL HARMONIC DISTORTION (Please refer to TOTAL HARMONIC DISTORTION(THD) section) INPUT EFFICIENCY (Typ.) 90% 90% 91% 88% 89% AC CURRENT 1.1A / 115VAC 0.6A / 230VAC 0.5A/277VAC INRUSH CURRENT(Typ.) COLD START 60A(twidth=850s measured at 50% Ipeak) at 230VAC Per NEMA 410 MAX. No. of PSUs on 16A 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC No load power consumption <0.5W for Blank / A / Dx / D2-Type NO LOAD / STANDBY POWER CONSUMPTION Standby power consumption <0.5W for B / DA-Type 95 ~ 108% OVER CURRENT Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed PROTECTION 28 ~ 34V 41 ~ 48V 47 ~ 54V 54 ~ 62V 62 ~ 72V OVER VOLTAGE Shut down output voltage, re-power on to recover OVER TEMPERATURE Shut down output voltage, re-power on to recover WORKING TEMP. Tcase=-40 ~ +90 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=+90 20 ~ 95% RH non-condensing WORKING HUMIDITY -40 ~ +80, 10 ~ 95% RH ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 0.03%/ (0 ~ 60) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750(typeHL), CSA C22.2 No. 250.13-12 ENEC EN61347-1, EN61347-2-13 independent, EN62384 SAFETY STANDARDS GB19510.1, GB19510.14 IP65 or IP67 approved DALI STANDARDS Compliance to IEC62386-101, 102, 207 for DA-Type only WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH EMC EMC EMISSION Compliance to EN55015,EN61000-3-2 Class C ( load60%) EN61000-3-3 GB17743, GB17625.1 Compliance to EN61000-4-2,3,4,5,6,8,11 EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV) EMC IMMUNITY MTBF 978.2K hrs min. Telcordia SR-332 (Bellcore) 282.9Khrs min. MIL-HDBK-217F (25) 199*63*35.5mm (L*W*H) OTHERS DIMENSION 0.75kg 16pcs/13kg/0.72CUFT PACKING * , CH , , -(/* . , , NOTE 7 I / C% H = H> H J I > *& 8(45 ((4 , , , 0 - K , ( 0 I 0 &0 , 0 ( K 19 1 D . & , 0 7 = * * * = 8 , , HC+H>> , , 9 , 0 , 0 : , = , 0 , : , , , &: , < , G.( ((( 0 7 <( 3 7 0 , *C ) L 0 D++000 , 0 , File Name:ELG-100-SPEC 2016-08-30