70W Single Output Switching Power Supply HSG-70 series % & ( )& * + , % ) &- . ) /01 & . & IP65 SPECIFICATION MODEL HSG-70-12 HSG-70-18 HSG-70-24 HSG-70-36 HSG-70-48 DC VOLTAGE 12V 18V 24V 36V 48V CONSTANT CURRENT REGION Note.5 7.7 ~ 12V 11.3 ~ 18V 15.5 ~ 24V 22.1 ~ 36V 29.3 ~ 48V RATED CURRENT 5.0A 4.0A 3.0A 2.0A 1.5A 60W 72W 72W 72W 72W RATED POWER Can be adjusted by internal potentiometer CURRENT ADJ. RANGE 3 ~ 5A 2.4 ~ 4A 1.8 ~ 3A 1.2 ~ 2A 0.9 ~ 1.5A OUTPUT RIPPLE & NOISE (max.) Note.2 150mVp-p 200mVp-p 200mVp-p 200mVp-p 200mVp-p VOLTAGE TOLERANCE Note.3 2.5% 2.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 2.0% 1.5% 0.5% 0.5% 0.5% SETUP, RISE TIME Note.7 2000ms,80ms / 115VAC 500ms,80ms / 230VAC at full load HOLD UP TIME 16ms at full load 230VAC/115VAC VOLTAGE RANGE Note.4 90 ~ 305VAC 127~431VDC FREQUENCY RANGE 47 ~ 63Hz PF0.96/115VAC, PF 0.96/230VAC,PF>0.92/277VAC at full load(please refer t Power Factor characteristic curve ) POWER FACTOR(Typ.) THD< 20% when output loading65% at 115VAC/230VAC input and output loading 75% at 277VAC input TOTAL HARMONIC DISTORTION INPUT 88% 89% 89% 90% 90% EFFICIENCY(Typ.) AC CURRENT 0.85A/115VAC 0.425A/230VAC 0.4A/277VAC INRUSH CURRENT(Typ.) COLD START 55A(twidth=340s measured at 50% Ipeak) at 230VAC MAX. No. of PSUs on 16A 6 units (circuit breaker of type B) / 11 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC 95 ~ 108% OVER CURRENT Note.5 Protection type : Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Protection type : Hiccup mode, recovers automatically after fault condition is removed. 14 ~ 17V 21 ~ 25V 28 ~ 34V 41 ~ 48V 54 ~ 63V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, re-power on to recover OVER TEMPERATURE WORKING TEMP. -40 ~ +70(Refer toDerating Curv) WORKING HUMIDITY 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ENVIRONMENT STORAGE TEMP., HUMIDITY 0.03%/ (0 ~ 50) TEMP. COEFFICIENT 10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes VIBRATION GB19510.14, GB19510.1, IP65 approved design refer to TUV EN61347-1, EN61347-2-13, UL8750 SAFETY STANDARDS I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25/ 70%RH EMC EMC EMISSION Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C(65% load) EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11 EN61547, EN55024, light industry level (surge 4KV), criteria A MTBF 338.2Khrs min. MIL-HDBK-217F (25) OTHERS DIMENSION 127.2*90*38.8mm (L*W*H) PACKING 0.76Kg 16pcs/ 13.2Kg/0.77CUFT 23 4 5 & 6 - 6 ) 3 NOTE 637 8 6 9%, ) . )& 26: . . . 32 8 < 3 35 - 3 3 1 & ) . - = 3 3 . + (>2 ( 35 ) /01 -) & 3 +35 . & . ) ) . 3 09 . ) )& - & 09 1 3 <3/ 35 4 . & & 3 3To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. File Name:HSG-70-SPEC 2015-11-0270W Single Output Switching Power Supply HSG-70 series Mechanical Specification Case No.209B Unit:mm 127.2 112.5 103.2 100 32020 10 V+(Brown) Io ADJ. V-(Blue) 2 CCC 1.5mm 2C AC/L(Brown) T case 23 AC/N(Blue) FG (Green/Yellow) 2 H05RN-F 1.0mm 3C 9.6 T case: Max. Case Temperature IP65 rated. Constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) Block Diagram RECTIFIERS EMI FILTER POWER PFC +V I/P & & SWITCHING CIRCUIT -V RECTIFIERS FILTER O.L.P. O.T.P. O.L.P. DETECTION FG CIRCUIT PWM & PFC CONTROL O.V.P. DeratingDerating Curve Curve Static Characteristics 100 100 90 80 80 230VAC Input only 70 60 60 40 50 20 40 -40 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 90 100 125 135 145 155 165 175 180 200 230 305 AMBIENT TEMPERATURE () INPUT VOLTAGE (V) 60Hz File Name:HSG-70-SPEC 2015-11-02 LOADLOADLOAD (%) (%) (%) LOAD (%) 15 27.5 4.5 55 17.5 90 38.8