LPF-16D-30P Mean Well

16W Constant Current Mode LED Driver LPF-16D series Users Manual IP30 7 8 44 : ) 9 - 4 % 0 4 3 - % +- <& & - - % & ( ) &* + , - .&/0 0 ( %& 1 23 + ( , - - 4 3 ( , 5 % = ( - - 6 7 ) & ) )* % % *) *. &* 8 6 9 File Name:LPF-16D-SPEC 2021-09-0316W Constant Current Mode LED Driver L PF -16D series SPECIFICATION MODEL LPF-16D-12 LPF-16D-15 LPF-16D-20 LPF-16D-24 LPF-16D-30 LPF-16D-36 LPF-16D-42 LPF-16D-48 LPF-16D-54 36V 42V DC VOLTAGE 12V 15V 20V 24V 30V 48V 54V 0.45A 0.39A RATED CURRENT 1.34A 1.07A 0.8A 0.67A 0.54A 0.34A 0.3A RATED POWER Note.5 16.08W 16.05W 16W 16.08W 16.2W 16.2W 16.38W 16.32W 16.2W 19.8 ~ 36V 23.1 ~ 42V OUTPUT CONSTANT CURRENT REGION Note.2 6.6 ~12V 8.25 ~ 15V 11 ~ 20V 13.2 ~ 24V 16.5 ~ 30V 26.4 ~ 48V 29.7 ~ 54V 5.0% max. rated current CURRENT RIPPLE CURRENT TOLERANCE 5.0% SETUP, RISE TIME Note.6 1500ms, 80ms / 115VAC 500ms, 80ms / 230VAC 16ms/230VAC 16ms/115VAC HOLD UP TIME (Typ.) 90 ~ 305VAC 127 ~ 431VDC VOLTAGE RANGE Note.5 (Please refer toSTATIC CHARACTERISTI section) FREQUENCY RANGE 47 ~ 63Hz PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC full load POWER FACTOR (Please refer toPOWER FACTOR (PF) CHARACTERISTI section) THD< 20%( load60%/115VC,230VAC load75%/277VAC) TOTAL HARMONIC DISTORTION (Please refer to TOTAL HARMONIC DISTORTION(THD) section) INPUT EFFICIENCY (Typ.) 83% 83% 84.5% 84.5% 84.5% 85% 85% 85% 84.5% AC CURRENT 0.4A / 115VAC 0.25A / 230VAC 0.2A/277VAC INRUSH CURRENT(Typ.) COLD START 45A(twidth=200s measured at 50% Ipeak) at 230VAC Per NEMA 410 MAX. No. of PSUs on 16A 14 units (circuit breaker of type B) / 24 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 240VAC 95 ~ 108% OVER CURRENT Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed. PROTECTION 34 ~ 40V 46 ~ 54V 59 ~ 66V 15 ~ 18V 17.5 ~ 21V 23 ~ 27V 28 ~ 35V 41 ~ 49V 54 ~ 63V OVER VOLTAGE Shut down and latch off o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE WORKING TEMP. Tcase=-35 ~ +70 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=+70 20 ~ 95% RH non-condensing WORKING HUMIDITY -40 ~ +80, 10 ~ 95% RH ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 0.03%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750, CSA C22.2 No. 250.0-08, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent,BS EN/EN62384, SAFETY STANDARDS Note.8 EAC TP TC 004,GB19510.1,GB19510.14 approved, IP67(optional) Design refer to UL60950-1 WITHSTAND VOLTAGE I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH EMC Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C ( load55%) BS EN/EN61000-3-3,GB17743 and GB17625.1, EMC EMISSION Note.8 EAC TP TC 020 EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11 BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 MTBF 1249.2K hrs min. Telcordia SR-332 (Bellcore) 420.1Khrs min. MIL-HDBK-217F (25) 148*40*32mm (L*W*H) OTHERS DIMENSION PACKING 0.21Kg 40pcs/9.4Kg/ 1.02CUFT NOTE 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains.