30W Single Output LED Power Supply PLN-30 series % & ( & ) *+ % , & - . & /001 % 2 ,34 5 6 & & & .. 7 +8 +8 7 +8 IP64 LPS SPECIFICATION MODEL PLN-30-9 PLN-30-12 PLN-30-15 PLN-30-20 PLN-30-24 PLN-30-27 PLN-30-36 PLN-30-48 DC VOLTAGE 9V 12V 15V 20V 24V 27V 36V 48V CONSTANT CURRENT REGION Note.6 6.3 ~ 9V 8.4 ~ 12V 10.5 ~ 15V 14 ~ 20V 16.8 ~ 24V 18.9 ~ 27V 25.2 ~ 36V 33.6 ~ 48V RATED CURRENT 3.3A 2.5A 2A 1.5A 1.25A 1.12A 0.84A 0.63A CURRENT RANGE 0 ~ 3.3A 0 ~ 2.5A 0 ~ 2A 0 ~ 1.5A 0 ~ 1.25A 0 ~ 1.12A 0 ~ 0.84A 0 ~ 0.63A RATED POWER 29.7W 30W 30W 30W 30W 30.24W 30.24W 30.24W RIPPLE & NOISE (max.) Note.2 2.6Vp-p 2Vp-p 2.6Vp-p 2.6Vp-p 2.6Vp-p 2.3Vp-p 4.5Vp-p 3.7Vp-p OUTPUT VOLTAGE ADJ. RANGE Note.5 -5% ~ 10%. Can be adjusted by internal potentiometer SVR1 CURRENT ADJ. RANGE Note.5 3% ~ -25%. Can be adjusted by internal potentiometer SVR2 VOLTAGE TOLERANCE Note.3 10% LINE REGULATION 3.0% LOAD REGULATION 5.0% SETUP TIME 500ms / 230VAC 3000ms / 115VAC at full load VOLTAGE RANGE Note.4 90 ~ 295VAC 127 ~ 417VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer toPower Factor Characteristi curve) TOTAL HARMONIC DISTORTION THD< 20% when output loading75% at 115VAC/230VAC input and output loading 80% at 277VAC input INPUT EFFICIENCY (Typ.) 80% 82.5% 83.5% 84% 84% 84.5% 85% 85.5% AC CURRENT (Typ.) 0.4A/115VAC 0.2A/230VAC 0.15A/277VAC INRUSH CURRENT (Typ.) COLD START 35A(twidth=25s measured at 50% Ipeak) at 230VAC MAX. No. of PSUs on 16A 64 units (circuit breaker of type B) / 64 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.5mA / 240VAC 100 ~ 110% OVER CURRENT Protection type : Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed. 10 ~ 14V 14 ~ 17V 17 ~ 22V 23 ~ 26V 27 ~ 34V 31 ~ 35V 40 ~ 50V 53 ~ 63V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, re-power on to recover -30 ~ +50 (Refer toDerating Curv) WORKING TEMP. 20 ~ 95% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH TEMP. COEFFICIENT 0.06%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes UL879, UL1310, CSA C22.2 No. 207-M89(except for 48V), TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No.223-M91 SAFETY STANDARDS (except for 48V),IP64, J61347-1,J61347-2-13 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH EMC EMC EMISSION Compliance to EN55015, EN61000-3-2 Class C (pin25W), Class D (>70% load) EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level, criteria B MTBF 621.4Khrs min. MIL-HDBK-217F (25) OTHERS DIMENSION 145*47*30mm (L*W*H) 0.22Kg 60pcs/14.2Kg/1.25CUFT PACKING /6 5 9 :0 - 6 NOTE 6 < 0=2> & / & %& & 06/ <+ 6 :69 - 6 +64 & 6 A 6 6 ( / B ( 6 *6 4 ) )5.=392 4 ,34= 4 ,3 6 69 & & & C 6 3= & - C %C 3= 4 6 864 ,34 - 6 69 C 3 7 - ,34 & & & 6 File Name:PLN-30-SPEC 2015-05-2830W Single Output LED Power Supply PLN-30 series Mechanical Specification Case No.964A Unit:mm 145 4.38 32020 2-R2.25 +V(Red) 32020 -V(Black) 61 SVT 18AWG2C AC/L(Brown) Tcase AC/N(Blue) SVT 18AWG2C 4.38 T case: Max. Case Temperature. Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram. SVR2 SVR1 SVR1 Output voltage adjustment SVR2 Output current adjustment Block Diagram fosc : 39KHz(115VAC) 53KHz(230VAC) RECTIFIERS EMI FILTER POWER +V I/P & & SWITCHING -V RECTIFIERS FILTER DETECTION CIRCUIT O.L.P. PWM & PFC CONTROL O.C.P. O.V.P. DeratingDerating Curve Curve Static Characteristics 100 100100 90 8080 80 70 6060 60 4040 50 2020 40 -30 -25-25 -5-5 00 1155 3300 40 50 60 90 100 125 135 145 155 165 175 180 200 230 295 AMBIENT TEMPERATURE () INPUT VOLTAGE (V) 60Hz File Name:PLN-30-SPEC 2015-05-28 LOADLOADLOAD (%) (%) (%) 9.83 47 23.5 LOAD (%) 9.83 30