1500W Single Output Power Supply SE-1500 s e ri e s Features : AC input 180 ~ 264VAC AC input active surge current limiting Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC ball bearing fan 3 High power density 7.8w/inch With DC OK signal output Built-in remote ON-OFF control Built-in remote sense function UL / CUL approved Low cost 2 years warranty SPECIFICATION MODEL SE-1500-5 SE-1500-12 SE-1500-15 SE-1500-24 SE-1500-27 SE-1500-48 DC VOLTAGE 5V 12V 15V 24V 27V 48V RATED CURRENT 300A 125A 100A 62.5A 55.6A 31.3A CURRENT RANGE 0 ~ 300A 0 ~ 125A 0 ~ 100A 0 ~ 62.5A 0 ~ 55.6A 0 ~ 31.3A RATED POWER 1500W 1500W 1500W 1500W 1501.2W 1502.4W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p OUTPUT VOLTAGE ADJ. RANGE 3.3 ~ 5.5V 10.8 ~ 13.5V 13.5 ~ 16.5V 21.6 ~ 26.4V 25 ~ 30V 43.2 ~ 56V VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 2.0% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 150ms, 12ms / 230VAC at full load HOLD UP TIME (Typ.) 26ms / 230VAC at full load VOLTAGE RANGE 180 ~ 264VAC 254 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 81% 85% 85% 87% 88% 89% INPUT 17.5A / 230VAC AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 60A / 230VAC LEAKAGE CURRENT <3.5mA / 240VAC 105 ~ 125% rated output power OVERLOAD Protection type : Shut down o/p voltage, re-power on to recover 5.75 ~ 6.75V 14.5 ~ 16.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 35V 57.6 ~ 67.2V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover 95 5 (5V), 85 5 (12V,15V), 80 5 (24V), 75 5 (27V,48V) (TSW1) detect on heatsink of o/p diode OVER TEMPERATURE Protection type : Shut down o/p voltage, recovers automatically after temperature goes down DC OK SIGNAL PSU turn on:3.3V ~ 5.6V PUS turn off:0 ~ 1V FUNCTION RC+/RC-: 0 ~ 0.8V power on 4 ~ 10V power off REMOTE CONTROL -20 ~ +70 (Refer toDerating Curv) WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.05%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1 approved SAFETY WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH MTBF 134.5K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 278*177.8*63.5mm (L*W*H) 3.3Kg 4pcs/14.2Kg/1.14CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12 twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. File Name:SE-1500-SPEC 2011-08-231500W Single Output Power Supply SE-1500 s e ri e s Mechanical Specification Case No.982A Unit:mm 278 236.3 27 40 8-M4(Both Sides) L=8mm 236.3 27 4-M4 L=5mm OUTPUT Air flow direction 16max. Terminal Pin No. Assignment : Control Pin (CN3) : JST B6B-XH or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating Housing Terminal 1 AC/L 1 DC OK Signal 4 +S JST XHP JST SXH-001T 2 AC/N 2 DC OK GND 5 RC- or equivalent or equivalent 3 FG 3 -S 6 RC+ fosc : 65KHz Block Diagram +S ACTIVE RECTIFIERS EMI POWER +V INRUSH I/P RECTIFIERS & CURRENT FILTER SWITCHING -V FILTER LIMITING -S O.V.P. O.L.P. PWM DETECTION CONTROL CIRCUIT DC OK O.T.P. FAN LOCK REMOTE RC CONTROL PROTECTION AUX FAN POWER Derating Curve Static Characteristics 100 100 90 80 80 70 60 60 40 50 20 40 180 190 200 230 264 -20 0 10 20 30 40 50 60 70 (HORIZONTAL) AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name:SE-1500-SPEC 2011-08-23 LOAD (%) LOAD (%) 162 7.9 38 12.5 13 10 4 20 63.5 177.8 +V ADJ -V + L N 6 1 TB1 LED 1 2 3 CN3