25W DC-DC Triple Output Converter T KA3 0 seri es Features : E2:1 wide input range E4:1 wide input range(option) E1000VDC I/O isolation EBuilt-in EMI filter ERemote ON-OFF control EProtections: Short circuit / Overload ECooling by free air convection ESix-sided shield metal case EEpoxy encapsulated E100% burn-in test EApprovals: FCC / CE E2 years warranty SPECIFICATION ORDER NO. TKA30A-B TKA30B-B TKA30C-B TKA30A-C TKA30B-C TKA30C-C DC VOLTAGE +5V 12V +5V 15V CURRENT RANGE 700 ~ 3500mA 62 ~ 310mA 700 ~ 3500mA 50 ~ 250mA RATED POWER 25W RIPPLE & NOISE (max.) Note.2 100mVp-p OUTPUT LINE REGULATION Note.3 0.5% 1.0% 1.0% 0.5% 1.0% 1.0% LOAD REGULATION Note.4 +5V: 2.0% , V : 5.0% 1 VOLTAGE ACCURACY +5V: 2.0% , V : 5.0% 1 SWITCHING FREQUENCY 100KHz min. A: 9 ~ 18VDC B: 18~36VDC C: 36~72VDC VOLTAGE RANGE 80% 82% 82% 80% 82% 82% EFFICIENCY (Typ.) Full load A: 2.61A B: 1.27A C: 0.64A INPUT DC CURRENT No load A: 40mA B: 18mA C: 10mA FILTER Pi network PROTECTION Fuse recommended 110 ~ 250% rated output power OVERLOAD Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION (Note. 5) All output equipped with short circuit SHORT CIRCUIT Protection type : Hiccup mode, recovers automatically after fault condition is removed -40 ~ +85J (Refer to output load derating curve) WORKING TEMP. 20% ~ 90% RH non-condensing WORKING HUMIDITY STORAGE TEMP., HUMIDITY -40 ~ +105J, 10 ~ 95% RH ENVIRONMENT 0.03% /J (0 ~ 50J) TEMP. COEFFICIENT 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes VIBRATION WITHSTAND VOLTAGE I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25J/ 70% RH SAFETY & ISOLATION RESISTANCE EMC EMISSION Compliance to EN55022 Class B, FCC part 15 Class B EMC Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A EMC IMMUNITY REMOTE CONTROL Power on: R.C ~-Vin > 4.5~5.5VDC or open, Power off: R.C~ -Vin <0.8VDC or short MTBF 100Khrs min. MIL-HDBK-217F(25J) OTHERS DIMENSION 50.8*50.8*21.0mm or 2 *2 *0.82 inch (L*W*H) 110g WEIGHT Pin Configuration Derating Curve Mechanical Specification Unit: mm (inch) 21 ( 0.82 ) 30.48 (1.20) 1.0r + 0.2/-0.1 Pin No. Output 100 1 R.C 5 6 7 8 2 No Pin 80 3 -Vin BOTTOM SIDE 4 +Vin VIEW VIEW 5 +Vout 12.7 ( 0.50 ) 6 +5V 7 COM 4 3 2 1 8 -Vout 22.9 ( 0.90 ) 15.24 ( 0.60 ) 5.8 ( 0.23 ) -40 0 25 50 71 85 100 2.5( 0.10 ) 50.8 ( 2.00) Ta (J) 1.All parameters are specified at normal input, rated load, 25J 70% RH ambient. NOTE 2.Ripple & noise are measured at 20MHz by using a 12 twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds. File Name:TKA30-SPEC 2012-07-18 45.72 ( 1.80 ) 50.8 ( 2.00 ) LOAD (%)