1N5729B Microchip

1N5728B thru WWW.Microsemi .COM 1N5757B-1 1N5728B thru 1N5757B-1 DO-35 Axial-Leaded 500 mW Zener Diodes SCOTTSDALE DIVISION DESCRIPTION APPEARANCE The 1N5728 thru 1N5757 series of 0.5 watt Zener Voltage Regulators DO-35 provides a selection from 4.7 to 75 volts in standard 5% tolerances as well (DO-204AH) as tighter tolerances identified by a C or D suffix letter on the part number. These glass axial-leaded DO-35 Zeners are also available with an internal-metallurgical-bond option by adding a -1 suffix. Microsemi also offers numerous other Zener products to meet higher and lower power applications. IMPORTANT: For the most current data, consult MICROSEMIs website: 1N5728B thru WWW.Microsemi .COM 1N5757B-1 1N5728B thru 1N5757B-1 DO-35 Axial-Leaded 500 mW Zener Diodes SCOTTSDALE DIVISION ELECTRICAL CHARACTERISTICS* MAXIMUM REGULATOR TEST DYNAMIC REVERSE I TEST TEMPERATURE R REGULATOR TYPE VOLTAGE CURRENT IMPEDANCE CURRENT VOLTAGE COEFFICIENT CURRENT NUMBER (Note 1) (V ) (I ) (Z ) I (V ) (I ) ( ) Z Z Z R R ZM VZ o Amps Ohms Volts Volts A mA mV/ C 1N5728B 4.7 10 70 3.0 2 70 -1.0 1N5729B 5.1 10 50 3.0 2 65 -0.2 1N5730B 5.6 10 25 3.0 2 60 +1.2 1N5731B 6.2 10 10 3.0 4 55 +2.3 1N5732B 6.8 10 10 3.0 4 50 +3.0 1N5733B 7.5 10 10 2.0 5 45 +4.0 1N5734B 8.2 10 15 1.0 5 40 +5.0 1N5735B 9.1 10 15 0.5 6 40 +6.0 1N5736B 10 10 20 0.2 7 35 +7.0 1N5737B 11 5 20 0.1 8 30 +8.0 1N5738B 12 5 25 0.1 8 30 +9.0 1N5739B 13 5 30 0.1 9 25 +10.5 1N5740B 15 5 30 0.1 10 25 +12.9 1N5741B 16 5 40 0.1 11 20 +13 1N5742B 18 5 45 0.1 12 20 +15 1N5743B 20 5 55 0.1 14 15 +17 1N5744B 22 5 55 0.1 15 15 +19 1N5745B 24 5 70 0.1 17 15 +21 1N5746B 27 2 80 0.1 19 10 +23.5 1N5747B 30 2 80 0.1 21 10 +26 1N5748B 33 2 90 0.1 23 10 +29 1N5749B 36 2 90 0.1 25 10 +31 1N5750B 39 2 130 0.1 27 9 +34 1N5751B 43 2 150 0.1 30 9 +37 1N5752B 47 2 170 0.1 33 8 +40 1N5753B 51 2 180 0.1 36 7 +44 1N5754B 56 2 200 0.1 39 6 +47 1N5755B 62 2 215 0.1 43 6 +51 1N5756B 68 2 240 0.1 48 5 +56 1N5757B 75 2 255 0.1 53 5 +60 *JEDEC Registered Data. The Type Number indicates 5% Tolerance. (See Note 1.) NOTES: 1. Devices listed have a +/-5% voltage tolerance on nominal Vz with a B suffix. An A suffix is +/-10% and no suffix is +/-20%. Suffix C denotes a +/-2% tolerance and suffix D denotes a +/-1% tolerance. 2. All static parameters measured under pulsed conditions, tp = 300 s. 3. Dynamic Impedance is derived by measuring the ac voltage when superimposing an ac rms current of 0.2 mA at 1000 Hz on to the dc level of I . ZT Copyright 2003 Microsemi Page 2 11-03-2003 REV A Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503