24LC00T-I/SN Microchip

24XX00 24XX00 24XX00 24AA00/24LC00/24C00 2 128 Bit I C Bus Serial EEPROM Device Selection Table Package Types 8-PIN PDIP/SOIC Device VCC Range Temp Range 1 8 NC VCC 24AA00 1.8 - 5.5 C,I NC 2 7 NC 24LC00 2.5 - 5.5 C,I 24C00 4.5 - 5.5 C,I,E 3 6 NC SCL 4 5 Vss SDA Features 8-PIN TSSOP Low-power CMOS technology 1 8 - 500 A typical active current NC VCC 2 7 NC NC - 250 nA typical standby current 3 6 NC SCL Organized as 16 bytes x 8 bits 4 5 VSS SDA 2 2-wire serial interface bus, I C compatible 100 kHz (1.8V) and 400 kHz (5V) compatibility 5-PIN SOT-23 Self-timed write cycle (including auto-erase) 15 VCC SCL 4 ms maximum byte write cycle time 2 VSS 1,000,000 erase/write cycles SDA ESD protection > 4 kV 3 4 NC Data retention > 200 years 8L DIP, SOIC, TSSOP and 5L SOT-23 packages Block Diagram Standard or Pb-free finish available HV Generator Temperature ranges available: - Commercial (C): 0Cto +70C I/O Memory - Industrial (I): -40Cto +85C Control Control EEPROM - Automotive (E): -40C to +125C XDEC Logic Logic Array Description SCL SDA YDEC The Microchip Technology Inc. 24AA00/24LC00/ 24C00 (24XX00*) is a 128-bit Electrically Erasable VCC PROM memory organized as 16 x 8 with a 2-wire serial Sense AMP R/W Control interface. Low voltage design permits operation down VSS to 1.8 volts for the 24XX00 version, and every version maintains a maximum standby current of only 1 A and Pin Function Table typical active current of only 500 A. This device was Name Function designed for where a small amount of EEPROM is needed for the storage of calibration values, ID VSS Ground numbers or manufacturing information, etc. The SDA Serial Data 24XX00 is available in 8-pin PDIP, 8-pin SOIC (150 mil), 8-pin TSSOP and the 5-pin SOT-23 packages. SCL Serial Clock VCC +1.8V to 5.5V (24AA00) +2.5V to 5.5V (24LC00) 2 I C is a trademark of Philips Corporation. +4.5V to 5.5V (24C00) *24XX00 is used in this document as a generic part number for NC No Internal Connection the 24AA00/24LC00/24C00 devices. 2003 Microchip Technology Inc. DS21178D-page 124AA00/24LC00/24C00 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-65C to +125C ESD protection on all pins..........................................................................................................................................4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS All Parameters apply across the Commercial (C): TA = 0C to +70C, VCC = 1.8V to 5.5V recommended operating ranges unless Industrial (I): TA = -40C to +85C, VCC = 1.8V to 5.5V otherwise noted Automotive (E) TA = -40C to +125C, VCC = 4.5V to 5.5V Parameter Symbol Min. Max. Units Conditions SCL and SDA pins: VIH 0.7 VCC V (Note) High-level input voltage Low-level input voltage VIL 0.3 VCC V (Note) Hysteresis of Schmitt Trigger VHYS .05 VCC V VCC 2.5V (Note) inputs Low-level output voltage VOL 0.4 V IOL = 3.0 mA, VCC = 4.5V IOL = 2.1 mA, VCC = 2.5V Input leakage current ILI 1 AVIN = VCC or VSS Output leakage current ILO 1 AVOUT = VCC or VSS Pin capacitance (all inputs/outputs) CIN, 10 pFVCC = 5.0V (Note) COUT TA = 25C, f = 1 MHz Operating current ICC Write 2 mA VCC = 5.5V, SCL = 400 kHz ICC Read 1 mA VCC = 5.5V, SCL = 400 kHz Standby current ICCS 1 AVCC = 5.5V, SDA = SCL = VCC Note: This parameter is periodically sampled and not 100% tested. FIGURE 1-1: BUS TIMING DATA THIGH TF TR TSU:STA SCL TSU:STO THD:DAT TSU:DAT TLOW SDA THD:STA TSP IN TBUF TAA SDA OUT DS21178D-page 2 2003 Microchip Technology Inc.