24LC014-EST Microchip

24AA014/24LC014 2 1K I C Serial EEPROM Device Selection Table Package Types SOIC, TSSOP PDIP, MSOP Part VCC Max Temp. Number Range Clock Range A0 1 8 VCC A0 1 8 VCC (1) 24AA014 1.8V - 5.5V 400 kHz I A1 2 7 WP 2 7 A1 WP 24LC014 2.5V - 5.5V 400 kHz I A2 3 6 SCL 3 6 A2 SCL Note 1: 100 kHz for VCC < 2.5V VSS 4 5 SDA 4 5 VSS SDA DFN/TDFN Features: 1 VCC Single-Supply with Operation Down to 1.8V A0 8 7 WP A1 2 Low-Power CMOS Technology: 6 SCL A2 3 - 1 mA active current, typical VSS 4 5 SDA -1 A standby current, typical at 5.5V Organized as a Single Block of 128 Bytes (128 x 8) Block Diagram Hardware Write Protection for Entire Array 2 WP A0 A1 A2 C Compatible 2-Wire Serial Interface Bus, I HV Generator 100 kHz and 400 kHz Clock Compatibility Page Write Buffer for up to 16 Bytes I/O Memory Control Self-Timed Write Cycle (including auto-erase) Control EEPROM Logic XDEC Logic 5 ms max. Write Cycle Time Array Address Lines Allow up to Eight Devices on Bus 1,000,000 Erase/Write Cycles SDA SCL ESD Protection > 4,000V Write-Protect Circuitry VCC Data Retention > 200 Years YDEC 8-pin PDIP, SOIC, TSSOP, DFN, TDFN and VSS MSOP Packages Sense Amp. Available for Extended Temperature Ranges: R/W Control - Industrial (I): -40C to+85C Pb-Free and RoHS compliant Pin Function Table Description: Name Function VSS Ground The Microchip Technology Inc. 24AA014/24LC014 is a 1 Kbit Serial Electrically Erasable PROM with opera- SDA Serial Data tion down to 1.8V. The device is organized as a single SCL Serial Clock block of 128 x 8-bit memory with a 2-wire serial inter- VCC Power Supply face. Low-current design permits operation with typical A0, A1, A2 Chip Selects standby and active currents of only 1 A and 1 mA, respectively. The device has a page write capability for WP Hardware Write-Protect up to 16 bytes of data. Functional address lines allow the connection of up to eight 24AA014/24LC014 devices on the same bus for up to 8 Kbits of contiguous EEPROM memory. The device is available in the standard 8-pin PDIP, 8-pin SOIC (150 mil), TSSOP, 2x3 DFN and TDFN and MSOP packages. 2008 Microchip Technology Inc. DS21809E-page 124AA014/24LC014 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V SS ......................................................................................................... -0.6V to VCC +1.0V All inputs and outputs w.r.t. V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins ................ 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS All parameters apply across the VCC = +1.8V to +5.5V specified operating ranges unless Industrial (I): TA = -40C to +85C otherwise noted. Parameter Symbol Min. Max. Units Conditions SCL and SDA pins: High-level input voltage VIH 0.7 VCC V Low-level input voltage VIL 0.3 VCC V Hysteresis of Schmitt Trigger inputs VHYS 0.05 VCC V (Note 1) Low-level output voltage VOL 0.40 V IOL = 3.0 mA, VCC = 4.5V IOL = 2.1 mA, VCC = 2.5V Input leakage current ILI 1 VIN = VSS or VCC, WP = Vss Output leakage current ILO 1 AVOUT = VSS or VCC Pin capacitance (all inputs/outputs) CIN, COUT 10 pFVCC = 5.0V (Note 1) TA = 25C, f = 1 MHz Operating current ICC Read 1 mA VCC = 5.5V, SCL = 400 kHz ICC Write 3 mA VCC = 5.5V Standby current ICCS 1 AVCC = 5.5V, SDA = SCL = VCC WP = VSS, A0, A1, A2 = VSS Note 1: This parameter is periodically sampled and not 100% tested. DS21809E-page 2 2008 Microchip Technology Inc.