24LC024H-E/MS Microchip

24AA024H/24LC024H 2 2K I C Serial EEPROM with Half-Array Write Protect Device Selection Table Description: Part VCC Max. Temp. The Microchip Technology Inc. 24AA024H/24LC024H is Number Range Clock Range a 2Kbit Serial Electrically Erasable PROM with operation down to 1.7V. The device is organized as a (1) I 24AA024H 1.7V-5.5V 400 kHz single block of 256 x 8-bit memory with a 2-wire serial interface. Low-current design permits operation with 24LC024H 2.5V-5.5V 1 MHz I, E maximum standby and active currents of only 1 A and Note 1: 100 kHz for VCC < 1.8V 400 A, respectively. The device has a page write capability for up to 16 bytes of data. Functional address lines allow the connection of up to eight 24AA024H/ Features: 24LC024H devices on the same bus for up to 16 Kbits Single-Supply with Operation Down to 1.7V of contiguous EEPROM memory. The device is Low-Power CMOS Technology: available in the standard 8-pin PDIP, 8-pin SOIC (150 mil), TSSOP, 2x3 TDFN and MSOP packages. - 400 A active current, max. -1 A standby current, max. Block Diagram Organized as a Single Block of 256 Bytes (256 x 8) WP A0 A1 A2 2 HV Generator 2-Wire Serial Interface Bus, I C Compatible Schmitt Trigger Inputs for Noise Suppression I/O Memory Output Slope Control to Eliminate Ground Bounce Control Control EEPROM Logic 100 kHz and 400 kHz Compatibility XDEC Logic Array 1 MHz Compatibility (LC) Page Write Buffer for up to 16 Bytes SDA SCL Self-Timed Write Cycle (including Auto-Erase) Write-Protect Hardware Write Protection for Half Array Circuitry VCC (80h-FFh) YDEC VSS Address Lines Allow up to Eight Devices on Bus Sense Amp. 1 Million Erase/Write Cycles R/W Control ESD Protection > 4,000V Data Retention > 200 Years Factory Programming (QTP) Available Package Types 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP PDIP, MSOP SOIC, TSSOP Packages Available for Extended Temperature Ranges: A0 1 8 VCC 1 8 A0 VCC - Industrial (I): -40C to +85C A1 2 7 WP 2 7 A1 WP - Automotive (E): -40C to +125C A2 3 6 SCL 3 6 A2 SCL Pb-Free and RoHS compliant VSS 4 5 SDA 4 5 VSS SDA TDFN A0 1 8 VCC 7 WP A1 2 SCL 6 A2 3 VSS 4 5 SDA 2008 Microchip Technology Inc. DS22102A-page 124AA024H/24LC024H 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins .................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS Electrical Characteristics: DC CHARACTERISTICS Industrial (I): VCC = +1.7V to 5.5V TA = -40C to +85C Automotive (E): VCC = +2.5V to 5.5V TA = -40C to +125C Param. Sym. Characteristic Min. Max. Units Conditions No. D1 A0, A1, A2, SCL, SDA and WP pins: D2 VIH High-level input voltage 0.7 VCC V D3 VIL Low-level input voltage 0.3 VCC V D4 VHYS Hysteresis of Schmitt 0.05 VCC V (Note) Trigger inputs (SDA, SCL pins) D5 VOL Low-level output voltage 0.40 V IOL = 3.0 ma VCC = 4.5V IOL = 2.1 ma VCC = 2.5V D6 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS D7 ILO Output leakage current 1 AVOUT = VSS or VCC D8 CIN, Pin capacitance 10 pFVCC = 5.0V (Note) COUT (all inputs/outputs) TA = 25C, f = 1 MHz D9 ICC Read Operating current 400 AVCC = 5.5V, SCL = 400 kHz ICC Write 3 mA VCC = 5.5V D10 ICCS Standby current 1 AVCC = 5.5V, SCL = SDA = VCC WP = VSS, A0, A1, A2 = VSS Note: This parameter is periodically sampled and not 100% tested. DS22102A-page 2 2008 Microchip Technology Inc.