25AA128T-I/SN Microchip

25AA128/25LC128 128K SPI Bus Serial EEPROM Device Selection Table Part Number VCC Range Page Size Temp. Ranges Packages 25AA128 1.8V-5.5V 64 Byte I MF, P, SN, SM, ST 25LC128 2.5V-5.5V 64 Byte I, E MF, P, SN, SM, ST Features Pin Function Table Maximum Clock: 10 MHz Name Function Low-Power CMOS Technology: - Write current (maximum): 5 mA at 5.5V, CS Chip Select Input 10 MHz SO Serial Data Output - Read current: 5 mA at 5.5V, 10 MHz WP Write-Protect - Standby current: 5 A at 5.5V VSS Ground 16,384 x 8-Bit Organization SI Serial Data Input 64-Byte Page SCK Serial Clock Input Self-Timed Erase and Write Cycles HOLD Hold Input (5 ms maximum) VCC Supply Voltage Block Write Protection: - Protect none, 1/4, 1/2 or all of array Description Built-In Write Protection: - Power-on/off data protection circuitry The Microchip Technology Inc. 25AA128/25LC128 (1) - Write enable latch (25XX128 ) are 128-Kbit Serial Electrically Erasable PROMs. The memory is accessed via a simple Serial - Write-protect pin Peripheral Interface (SPI) compatible serial bus. The Sequential Read bus signals required are a clock input (SCK) plus High Reliability: separate data in (SI) and data out (SO) lines. Access to - Endurance: 1,000,000 erase/write cycles the device is controlled through a Chip Select (CS) - Data retention: >200 years input. - ESD protection: >4000V Communication to the device can be paused via the RoHS Compliant hold pin (HOLD). While the device is paused, transitions on its inputs will be ignored, with the Temperature Ranges exception of Chip Select, allowing the host to service - Industrial (I): -40Cto +85C higher priority interrupts. - Extended (E): -40C to +125C Automotive AEC-Q100 Qualified Note 1: 25XX128 is used in this document as a Packages generic part number for the 25AA128/ 25LC128 devices. 8-Lead DFN, 8-Lead PDIP, 8-Lead SOIC, 8-Lead SOIJ and 8-Lead TSSOP TSSOP Rotated TSSOP PDIP/SOIC/SOIJ DFN 11 88 VCC 1 8 VCC CS CS CS 1 8 VCC 1 8 HOLD SCK SO 22 77 SO 2 7 HOLD HOLD SO 2 7 VCC 2 7 HOLD SI 3 6 SCK 3 6 VSS 3 6 SCK 33 66 SCK WP WP CS WP 4 5 SI 4 5 4 5 SI SO WP VSS VSS 44 55 SI VSS 2003-2021 Microchip Technology Inc. DS20001831G-page 125AA128/25LC128 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V SS ......................................................................................................... -0.6V to VCC +1.0V All inputs and outputs w.r.t. V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature under bias.............................................................................................................-40C to +125C ESD protection on all pins..........................................................................................................................................4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended period of time may affect device reliability. TABLE 1-1: DC CHARACTERISTICS A = -40C to +85C VCC = 1.8V to 5.5V Industrial (I): T DC CHARACTERISTICS Extended (E): TA = -40C to +125C VCC = 2.5V to 5.5V Param. Symbol Characteristic Minimum Maximum Units Conditions No. D1 VIH High-Level Input Voltage 0.7 VCC VCC+1 V D2 VIL1 -0.3 0.3 VCC VVCC 2.7V Low-Level Input Voltage D3 VIL2 -0.3 0.2 VCC VVCC < 2.7V D4 VOL 0.4 VIOL = 2.1 mA Low-Level Output Voltage D5 VOL 0.2 VIOL = 1.0 mA, VCC < 2.5V D6 VOH High-Level Output Voltage VCC -0.5 V IOH = -400 A D7 ILI Input Leakage Current 1 A CS = VCC, VIN = VSS or VCC D8 ILO Output Leakage Current 1 A CS = VCC, VOUT = VSS or VCC Internal Capacitance 7 pFTA = +25C, CLK = 1.0 MHz, D9 CINT (all inputs and outputs) VCC = 5.0V (Note 1) 5 mAVCC = 5.5V, FCLK = 10.0 MHz, SO = Open D10 ICC Read Operating Current CC = 2.5V, FCLK = 5.0 MHz 2.5 mAV SO = Open 5 mAVCC = 5.5V D11 ICC Write Operating Current 3 mAVCC = 2.5V 5 ACS = VCC = 5.5V, Inputs tied to VCC or VSS, +125C D12 ICCS Standby Current 1 ACS = VCC = 5.5V, Inputs tied to VCC or VSS, +85C Note 1: This parameter is periodically sampled and not 100% tested. DS20001831G-page 2 2003-2021 Microchip Technology Inc.