Features Incorporates the ARM7TDMI ARM Thumb Processor High-performance 32-bit RISC Architecture High-density 16-bit Instruction Set Leader in MIPS/Watt In-circuit Emulation, Debug Communication Channel Support EmbeddedICE Internal High-speed Flash 512 Kbytes (SAM7X512) Organized in Two Banks of 1024 Pages of 256 Bytes (Dual Plane) AT91SAM 256 Kbytes (SAM7X256) Organized in 1024 Pages of 256 Bytes (Single Plane) 128 Kbytes (SAM7X128) Organized in 512 Pages of 256 Bytes (Single Plane) ARM-based Single Cycle Access at Up to 30 MHz in Worst Case Conditions Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed Flash MCU Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities, Flash Security Bit SAM7X512 Fast Flash Programming Interface for High Volume Production SAM7X256 Internal High-speed SRAM, Single-cycle Access at Maximum Speed 128 Kbytes (SAM7X512) SAM7X128 64 Kbytes (SAM7X256) 32 Kbytes (SAM7X128) Memory Controller (MC) Embedded Flash Controller, Abort Status and Misalignment Detection Reset Controller (RSTC) Based on Power-on Reset Cells and Low-power Factory-calibrated Brownout Detector Provides External Reset Signal Shaping and Reset Source Status Clock Generator (CKGR) Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL Power Management Controller (PMC) Power Optimization Capabilities, Including Slow Clock Mode (Down to 500 Hz) and Idle Mode Four Programmable External Clock Signals Advanced Interrupt Controller (AIC) Individually Maskable, Eight-level Priority, Vectored Interrupt Sources Two External Interrupt Sources and One Fast Interrupt Source, Spurious Interrupt Protected Debug Unit (DBGU) 2-wire UART and Support for Debug Communication Channel interrupt, Programmable ICE Access Prevention Mode for General Purpose 2-wire UART Serial Communication Periodic Interval Timer (PIT) 20-bit Programmable Counter plus 12-bit Interval Counter Windowed Watchdog (WDT) 12-bit key-protected Programmable Counter Provides Reset or Interrupt Signals to the System Counter May Be Stopped While the Processor is in Debug State or in Idle Mode 6120IATARM06-Apr-11 Real-time Timer (RTT) 32-bit Free-running Counter with Alarm Runs Off the Internal RC Oscillator Two Parallel Input/Output Controllers (PIO) Sixty-two Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os Input Change Interrupt Capability on Each I/O Line Individually Programmable Open-drain, Pull-up Resistor and Synchronous Output Thirteen Peripheral DMA Controller (PDC) Channels One USB 2.0 Full Speed (12 Mbits per second) Device Port On-chip Transceiver, 1352-byte Configurable Integrated FIFOs One Ethernet MAC 10/100 base-T Media Independent Interface (MII) or Reduced Media Independent Interface (RMII) Integrated 28-byte FIFOs and Dedicated DMA Channels for Transmit and Receive One Part 2.0A and Part 2.0B Compliant CAN Controller Eight Fully-programmable Message Object Mailboxes, 16-bit Time Stamp Counter One Synchronous Serial Controller (SSC) Independent Clock and Frame Sync Signals for Each Receiver and Transmitter IS Analog Interface Support, Time Division Multiplex Support High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer Two Universal Synchronous/Asynchronous Receiver Transmitters (USART) Individual Baud Rate Generator, IrDA Infrared Modulation/Demodulation Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support Full Modem Line Support on USART1 Two Master/Slave Serial Peripheral Interfaces (SPI) 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects One Three-channel 16-bit Timer/Counter (TC) Three External Clock Inputs, Two Multi-purpose I/O Pins per Channel Double PWM Generation, Capture/Waveform Mode, Up/Down Capability One Four-channel 16-bit Power Width Modulation Controller (PWMC) One Two-wire Interface (TWI) 2 Master Mode Support Only, All Two-wire Atmel EEPROMs and I C Compatible Devices Supported One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os SAM-BA Boot Assistance Default Boot program Interface with SAM-BA Graphic User Interface IEEE 1149.1 JTAG Boundary Scan on All Digital Pins 5V-tolerant I/Os, Including Four High-current Drive I/O lines, Up to 16 mA Each Power Supplies Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components 3.3V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply 1.8V VDDCORE Core Power Supply with Brownout Detector Fully Static Operation: Up to 55 MHz at 1.65V and 85 C Worst Case Conditions Available in 100-lead LQFP Green and 100-ball TFBGA Green Packages 2 SAM7X512/256/128 6120IATARM06-Apr-11