MCP3002-I/SN Microchip

MCP3002 MCP3002 2.7V Dual Channel 10-Bit A/D Converter with SPI Serial Interface Features Description 10-bit resolution The MCP3002 is a successive approximation 10-bit analog-to-digital (A/D) converter with on-board sample 1 LSB maximum DNL and hold circuitry. 1 LSB maximum INL The MCP3002 is programmable to provide a single Analog inputs programmable as single-ended or pseudo-differential input pair or dual single-ended pseudo-differential pairs inputs. Differential Nonlinearity (DNL) and Integral On-chip sample and hold Nonlinearity (INL) are both specified at 1 LSB. Com- SPI serial interface (modes 0,0 and 1,1) munication with the device is done using a simple serial Single supply operation: 2.7V - 5.5V interface compatible with the SPI protocol. The device 200 ksps max sampling rate at V = 5V is capable of conversion rates of up to 200 ksps at 5V DD and 75 ksps at 2.7V. 75 ksps max sampling rate at V = 2.7V DD Low power CMOS technology: The MCP3002 operates over a broad voltage range, - 5 nA typical standby current, 2 A maximum 2.7V to 5.5V. Low-current design permits operation with a typical standby current of 5 nA and a typical active - 550 A maximum active current at 5V current of 375 A. Industrial temperature range: -40C to +85C The MCP3002 is offered in 8-pin MSOP, PDIP, TSSOP 8-pin MSOP, PDIP, SOIC and TSSOP packages and 150 mil SOIC packages. Applications Package Types Sensor Interface Process Control MSOP, PDIP, SOIC, TSSOP Data Acquisition CS/SHDN 1 8 V /V Battery Operated Systems DD REF CH0 2 7 CLK Functional Block Diagram CH1 3 6 D OUT 5 V 4 SS D V V IN SS DD Input CH0 Channel DAC CH1 Mux Comparator 10-Bit SAR Sample and Hold Shift Register Control Logic CS/SHDN D CLK D IN OUT 2000-2011 Microchip Technology Inc. DS21294E-page 1MCP3002 Notice: Stresses above those listed under Absolute 1.0 ELECTRICAL Maximum Ratings may cause permanent damage to the CHARACTERISTICS device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not Absolute Maximum Ratings implied. Exposure to maximum rating conditions for extended V ..................................................................................7.0V periods may affect device reliability. DD All Inputs and Outputs w.r.t. V ............. -0.6V to V +0.6V SS DD Storage Temperature.....................................-65C to +150C Ambient temperature with power applied.......-65C to +150C ESD Protection On All Pins (HBM) 4kV ELECTRICAL CHARACTERISTICS All parameters apply at V = 5V, T = -40C to +85C, f = 200 ksps and f = 16*f , unless otherwise DD A SAMPLE CLK SAMPLE noted. Typical values apply for V = 5V, T = +25C, unless otherwise noted. DD A PARAMETER SYM MIN TYP MAX UNITS CONDITIONS Conversion Rate: Conversion Time T 10 clock CONV cycles Analog Input Sample Time T 1.5 clock SAMPLE cycles Throughput Rate F 200 ksps V = 5V SAMPLE DD 75 ksps V = 2.7V DD DC Accuracy: Resolution 10 bits Integral Nonlinearity INL 0.5 1 LSB Differential Nonlinearity DNL 0.25 1 LSB No missing codes over temperature Offset Error 1.5 LSB Gain Error 1 LSB Dynamic Performance: Total Harmonic Distortion THD -76 dB V = 0.1V to 4.9V 1 kHz IN Signal to Noise and Distortion SINAD 61 dB V = 0.1V to 4.9V 1 kHz IN (SINAD) Spurious Free Dynamic Range SFDR 78 dB V = 0.1V to 4.9V 1 kHz IN Analog Inputs: Input Voltage Range for CH0 or V V V SS DD CH1 in Single-ended Mode Input Voltage Range for IN+ in IN+ IN- V +IN- DD Pseudo-Differential Mode Input Voltage Range for IN- in IN- V -100 V +100 mV SS SS Pseudo-Differential Mode Leakage Current 0.001 1 A Switch Resistance R 1K See Figure 4-1 SS Sample Capacitor C 20 pF See Figure 4-1 SAMPLE Note 1: This parameter is established by characterization and not 100% tested. 2: The sample cap will eventually lose charge, especially at elevated temperatures, therefore f 10 kHz for CLK temperatures at or above 70C. DS21294E-page 2 2000-2011 Microchip Technology Inc.