MCP8026-115E/PT Microchip

MCP8025A/6 3-Phase Brushless DC (BLDC) Motor Gate Driver with Power Module, Sleep Mode and LIN Transceiver Features Applications Quiescent Current: Industrial Fuel, Water, Ventilation Motors Home Appliances - Sleep mode: 5 A Typical Permanent Magnet Synchronous Motor (PMSM) - Standby mode: < 200 A Control LIN Transceiver Interface (MCP8025A): Hobby Aircraft, Boats, Vehicles - Compliant with LIN Bus Specifications 1.3, 2.2 and SAE J2602 Description - Supports baud rates up to 20 Kbaud The MCP8025A/6 devices are 3-phase Brushless DC - Internal pull-up resistor and diode (BLDC) power modules, containing three integrated - Protected against ground shorts half-bridge drivers, capable of driving three external - Protected against loss of ground NMOS/NMOS transistor pairs. The three half-bridge - Automatic thermal shutdown drivers are capable of delivering a peak output current - LIN bus dominant time-out of 0.5A at 12V for driving high-side and low-side NMOS MOSFET transistors. The drivers have shoot-through, Three Half-Bridge Drivers Configured to Drive overcurrent and short-circuit protection. A Sleep mode External High-Side NMOS and Low-Side NMOS has been added to achieve a typical key-off quiescent MOSFETs: current of 5 A. - Independent input control for high-side NMOS and low-side NMOS MOSFETs The MCP8025A device integrates a comparator, a buck voltage regulator, two LDO regulators, power monitoring - Peak output current: 0.5A at 12V comparators, an overtemperature sensor, a LIN trans- - Shoot-through protection ceiver, a zero-crossing detector, a neutral simulator and - Overcurrent and short-circuit protection an operational amplifier for motor current monitoring. The Adjustable Output Buck Regulator (750 mW) phase comparator and multiplexer allow for hardware Fixed Output Linear Regulators: commutation detection. The neutral simulator allows - 5V at 30 mA commutation detection without a neutral tap in the motor. - 12V at 30 mA The buck converter is capable of delivering 750 mW of power for powering a companion microcontroller. The Operational Amplifiers: buck regulator may be disabled if not used. The on-board - One in MCP8025A 5V and 12V Low-Dropout (LDO) voltage regulators are - Three in MCP8026 capable of delivering 30 mA of current. Overcurrent Comparator with DAC Reference The MCP8026 device replaces the LIN transceiver, Phase Comparator with Multiplexer (MCP8025A) neutral simulator and zero-crossing detector in Neutral Simulator (MCP8025A) MCP8025A with two level shifters, and two additional Level Translators (MCP8026) op amps. Input Voltage Range: 6V to 40V The MCP8025A/6 operation is specified over a Operational Voltage Range: temperature range of -40C to +150C. - 6V to 19V (MCP8025A) Package options include 40-Lead 5x5 QFN and - 6V to 28V (MCP8026) 48-Lead 7x7 TQFP with Exposed Pad (EP). Buck Regulator Undervoltage Lockout: 4V Undervoltage Lockout (UVLO): 5.5V (Except Buck) Overvoltage Lockout (OVLO): -20V (MCP8025A) -32V (MCP8026) Transient (100 ms) Voltage Tolerance: 48V Extended Temperature Range (T ): -40 to +150C A Thermal Shutdown 2018 Microchip Technology Inc. DS20005905C-page 1MCP8025A/6 Package Types MCP8025A 5 mm x 5 mm QFN-40 PWM2H 1 30 +12V PWM1L 2 29 VBA PWM1H 3 28 VBB CE 4 27 VBC EP LIN BUS 5 26 PHA (41) RX 6 25 PHB TX 7 24 PHC FAULTn/TXE 8 23 HSA MUX1 9 22 HSB MUX2 10 21 HSC 7 mm x 7 mm TQFP-48 + PWM1L 1 36 PGND PWM1H 2 35 PGND CE 3 34 +12V NC 4 33 VBA NC 5 32 VBB EP LIN BUS 6 31 VBC (49) PGND 7 30 PHA RX 8 29 PHB TX 9 28 PHC FAULTn/TXE 10 27 HSA MUX1 11 26 HSB MUX2 12 25 HSC * Includes Exposed Thermal Pad (EP), see Table 3-1. DS20005905C-page 2 2018 Microchip Technology Inc. ZC OUT 13 48 PWM2H ZC OUT 11 40 PWM2L COMP REF 14 47 PWM2L COMP REF 12 39 PWM3H ILIMIT OUT 15 46 PWM3H ILIMIT OUT 13 38 PWM3L I OUT1 16 45 PWM3L I OUT1 14 37 DE2 I SENSE1- 17 44 DE2 I SENSE1- 15 36 CAP1 I SENSE1+ 18 43 CAP1 I SENSE1+ 16 35 CAP2 PGND 19 42 CAP2 PGND 17 34 +5V PGND 20 41 +5V LSA 18 33 FB LSA 21 40 FB LSB 19 32 VDD LSB 22 39 VDD LSC 20 31 LX LSC 23 38 VDD PGND 24 37 LX