MIC2155YML-TR Microchip

MIC2155 Two-Phase Single-Output PWM Synchronous Buck Control IC Features General Description Synchronous Buck Control IC with Outputs The MIC2155 is a two-phase, single-output Switching 180 Degrees Out of Phase synchronous buck control IC that features small size, Remote Sensing with Internal Differential high efficiency, and a high level of flexibility. The IC Amplifier implements a 500 kHz Voltage mode PWM control with 4.5V-to-14.5V Input Voltage Range the outputs switching 180 degrees out of phase. The Adjustable Output Voltages down to 0.7V result of the out-of-phase operation is 1 MHz (or 600 1% Output Voltage Accuracy kHz) input ripple with ripple current cancellation, Starts up into a Pre-biased Output minimizing the required input filter capacitance. A 1% 500 kHz PWM Operation output voltage tolerance allows the maximum level of Adaptive Gate Drive allows Efficiencies of over system performance. Internal drivers with adaptive 95% gate drive allow the highest efficiency with the Adjustable Current Limit with no Sense Resistor minimum external components. Senses Low-Side MOSFET Current Two independent enable pins and a power good output Internal Drivers allow 25A per Phase are provided, allowing a high level of control and Power Good Output allows Simple Sequencing sequencing capability. Dual Enable Pins with Micro-Power Shutdown The MIC2155 has an operating junction temperature and UVLO ranging from 40C to +125C. Programmable Soft-Start Pin Data sheets and support documentation can be found Output Overvoltage Protection on the Microchip website at www.microchip.com. Works with Ceramic Output Capacitors Multi-Input Supply Capability Single-Output High-Current Capability with Master/Slave Current Sharing External Synchronization Small Footprint 32-Pin 5 mm 5 mm VQFN Junction Temperature Range of 40C to +125C Applications Multi-Output Power Supplies with Sequencing DSP, FPGA, CPU and ASIC Power Supplies DSL Modems Telecommunications and Networking Equipment Servers Package Type 32-lead 5 mm x 5 mm VQFN (Top view) 32 31 30 29 28 27 26 25 1 24 BST1 HSD2 HSD1 2 23 SW2 SW1 3 22 N/C CS1 4 21 VIN2 5 20 EN2 VOUT SS COMP2 6 19 COMP1 7 18 FB2 EP FB1 8 17 EA2+ 910 11 12 13 14 15 16 See Table 3-1 for pin information. 2019 Microchip Technology Inc. DS20006106A-page 1 DIFFOUT PGND1 RMVOUT LSD1 RMGND VIN1 AGND EN1 AVDD VDD N/C LSD2 SYNC PGND2 PGOOD BST2MIC2155 Functional Block Diagram AVDD BST1 (13) (1) Band BG gap (700mV) HSD1 (2) E/A1 FB1 SW1 (8) (3) Adap SET VDD S Q COMP1 -tive (7) + CLR 2uA BG Rmp1 R Q LSD1 - OutH Drive Clk1 (31) SS PGND1 + (6) BG +3% (32) - 200uA CS1 + BG -3% (4) - OC retry Current Limit + BG -25% - EN1 LOGIC (29) OV + BG +15% PGOOD - PG (16) VOUT + BG-10% - Pre-Bias VDD VIN1 Startup VOUT VDD UVLO (20) (28) Circuit EN1 VIN1 LDO (30) DIFFOUT (9) VIN1 UVLO RMVOUT (10) RMGND Rmp1 (11) Clk1 SYNC (15) Rmp2 BS2 Clk2 (25) 2 phase HSD2 Oscillator AVDD (24) FB2 E/A2 OutH (18) SW2 Gm (23) Adap EA2+ SET S Q VDD (17) -tive R CLR Q Rmp2 Drive LSD2 COMP2 Clk2 (27) (19) PGND2 SS (26) EN2 (5) VIN2 UVLO VOUT VIN2 10mV (21) AGND (12) DS20006106A-page 2 2019 Microchip Technology Inc.