PIC18F47J13 FAMILY PIC18F47J13 Family 28/44-Pin, High-Performance Microcontrollers with XLP Technology Power Management Features with XLP Peripheral Highlights (cont.): for eXtreme Low Power: Seven Capture/Compare/PWM (CCP) modules Two Master Synchronous Serial Port (MSSP) modules Deep Sleep mode: CPU Off, Peripherals Off, SRAM Off, featuring: Currents Down to 9 nA and 700 nA with RTCC: - 3-wire SPI (all 4 modes) - Able to wake-up on external triggers, programmable WDT - SPI Direct Memory Access (DMA) channel or RTCC alarm w/1024 byte count - Ultra Low-Power Wake-up (ULPWU) 2 -I C Master and Slave modes Sleep mode: CPU Off, Peripherals Off, SRAM On, Fast 8-Bit Parallel Master Port/Enhanced Parallel Slave Port Wake-up, Currents Down to 0.2 A, 2V Typical Three Analog Comparators with Input Multiplexing Idle: CPU Off, SRAM On, Currents Down to 12-Bit Analog-to-Digital (A/D) Converter module: 1.7 A Typical - Up to 13 input channels Run: CPU On, SRAM On, Currents Down to - Auto-acquisition capability 5.8 A Typical - 10-bit mode for 100 ksps conversion speed Timer1 Oscillator w/RTCC: 0.7 A, 32 kHz Typical - Conversion available during Sleep Watchdog Timer: 0.33 A, 2V Typical High/Low-Voltage Detect module Charge Time Measurement Unit (CTMU): Flexible Oscillator Structure: - Provides a precise resolution time measurement Two External Clock modes, Up to 48 MHz (12 MIPS) for both flow measurement and simple temperature Integrated Crystal/Resonator Driver sensing Low-Power 31 kHz Internal RC Oscillator - Supports capacitive touch sensing for touch Tunable Internal Oscillator (31 kHz to 8 MHz, screens and capacitive switches 0.15% Typical, 1% Max.) Two Enhanced USART modules: Precision 48 MHz PLL or 4x PLL Options - Supports RS-485, RS-232 and LIN/J2602 Low-Power Secondary Oscillator using Timer1 32 kHz - Auto-wake-up on Start bit Fail-Safe Clock Monitor (FSCM): - Auto-Baud Detect (ABD) - Allows for safe shutdown if any clock stops Programmable Reference Clock Output Generator Special Microcontroller Features: 5.5V Tolerant Inputs (digital only pins) Peripheral Highlights: Low-Power, High-Speed CMOS Flash Technology Peripheral Pin Select: C Compiler Optimized Architecture for Re-Entrant Code - Allows independent I/O mapping of many peripherals Priority Levels for Interrupts - Continuous hardware integrity checking and safety Self-Programmable under Software Control interlocks prevent unintentional configuration changes 8 x 8 Single-Cycle Hardware Multiplier Hardware Real-Time Clock/Calendar (RTCC): Extended Watchdog Timer (WDT): - Provides clock, calendar and alarm functions - Programmable period from 4 ms to 131s High-Current Sink/Source 25 mA/25mA Single-Supply In-Circuit Serial Programming (ICSP) (PORTB and PORTC) via Two Pins Four Programmable External Interrupts In-Circuit Debug (ICD) with 3 Breakpoints via Two Pins Four Input Change Interrupts Operating Voltage Range of 2.0V to 3.6V Three Enhanced Capture/Compare/PWM On-Chip 2.5V Regulator (ECCP) modules: Flash Program Memory of 10,000 Erase/Write Cycles - One, two or four PWM outputs Minimum and 20-Year Data Retention - Selectable polarity - Programmable dead time - Auto-shutdown and auto-restart - Pulse steering control 2010-2017 Microchip Technology Inc. DS30009974C-page 1PIC18FX7J13 TABLE 1: PIC18F47J13 FAMILY TYPES MSSP PIC18F SPI Device w/DMA PIC18F26J13 28 64K 3760 19 4/4 3/7 2 2 Y Y 10 3 Y N Y Y PIC18F27J13 28 128K 3760 19 4/4 3/7 2 2 Y Y 10 3 Y N Y Y PIC18F46J13 44 64K 3760 25 4/4 3/7 2 2 Y Y 13 3 Y Y Y Y PIC18F47J13 44 128K 3760 25 4/4 3/7 2 2 Y Y 13 3 Y Y Y Y PIC18LF26J13 28 64K 3760 19 4/4 3/7 2 2 Y Y 10 3 N N Y Y PIC18LF27J13 28 128K 3760 19 4/4 3/7 2 2 Y Y 10 3 N N Y Y PIC18LF46J13 44 64K 3760 25 4/4 3/7 2 2 Y Y 13 3 N Y Y Y PIC18LF47J13 44 128K 3760 25 4/4 3/7 2 2 Y Y 13 3 N Y Y Y 2010-2017 Microchip Technology Inc. DS30009974C-page 2 Pins Program Memory (bytes) SRAM (bytes) Remappable Pins Timers 8/16-Bit ECCP/CCP EUSART 2 I C 12-Bit A/D (ch) Comparators Deep Sleep PMP/PSP CTMU RTCC