TCM809/ TCM810 TCM809/TCM810 3-Pin Microcontroller Reset Monitors Features General Description Precision V Monitor for 2.5V, 3.0V, 3.3V, 5.0V The TCM809 and TCM810 are cost-effective system DD Nominal System Voltage Supplies supervisor circuits designed to monitor V in digital DD systems and provide a reset signal to the host proces- 140 msec Minimum RESET Time Out Period sor, when necessary. No external components are RESET Output to V = 1.0V (TCM809) DD required. Low Supply Current, 9 A (typ.) The RESET output is typically driven active within V Transient Immunity DD 65 sec of V falling through the reset voltage thresh- DD Small 3-Pin SC-70 and SOT-23B Packages old. RESET is maintained active for a minimum of No External Components 140 msec after V rises above the reset threshold. DD Push-Pull RESET Output The TCM810 has an active-high RESET output, while the TCM809 has an active-low RESET output. The out- Temperature Range: put of the TCM809/TCM810 is valid down to V = 1V. DD - Industrial, SC-70 (E): -40C to +85C Both devices are available in 3-Pin SC-70 and SOT-23B - Extended, SOT-23, SC-70 (V): -40C to +125C packages. The TCM809/TCM810 is optimized to reject fast Applications transient glitches on the V line. A low supply current DD Computers of 9 A (typ., V = 3.3V) make these devices suitable DD for battery-powered applications. Embedded Systems Battery-Powered Equipment Pin Configurations Critical Microcontroller Power Supply Monitoring Automotive SOT-23B/SC-70 Typical Application Circuit GND 1 V DD 3 V V DD 3 DD V DD PICmicro Microcontroller TCM809 RESET TCM809 2 TCM810 (RESET) 2 RESET RESET INPUT (Active-Low) Note: 3-Pin SOT-23B is equivalent to GND GND JEDEC TO-236. 1 2004 Microchip Technology Inc. DS21661C-page 1TCM809/TCM810 1.0 ELECTRICAL PIN FUNCTION TABLE CHARACTERISTICS NAME FUNCTION Absolute Maximum Ratings GND Ground. Supply Voltage (V to GND) ..........................................6.0V DD RESET (TCM809) RESET push-pull output RESET, RESET.................................... 0.3V to (V +0.3V) remains low while V is below DD DD the reset voltage threshold and Input Current, V .........................................................20 mA DD for 240 msec (140 msec min.) Output Current, RESET, RESET...................................20 mA after V rises above reset DD dV/dt (V ).............................................................100V/sec DD threshold. Operating Temperature Range.................... 40C to +125C RESET (TCM810) RESET push-pull output Power Dissipation (T = 70C): A remains high while V is below DD 3-Pin SOT-23B (derate 4 mW/C above +70C) ......320 mW the reset voltage threshold and 3-Pin SC-70 (derate 2.17 mW/C above +70C)......174 mW for 240 msec (140 msec min.) Storage Temperature Range....................... 65C to +150C after V rises above reset DD Maximum Junction Temperature, T .............................. 150C J threshold. Notice: Stresses above those listed under Maximum ratings may V Supply voltage (+2.5V, +3.0V, cause permanent damage to the device. This is a stress rating only and DD functional operation of the device at those or any other conditions +3.3V, +5.0V). above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended peri- ods may affect device reliability. ELECTRICAL CHARACTERISTICS V = Full Range, T = Operating Temperature Range, unless otherwise noted. Typical values are at T = +25C, DD A A V = 5V for L/M/J, 3.3V for T/S, 3.0V for R and 2.5V for Z (Note 1). DD Parameter Sym Min Typ Max Units Test Conditions V Range 1.0 5.5 V T = 0C to +70C DD A 1.2 5.5 T = 40C to +125C A Supply Current I 12 30 A TCM8xxL/M/J: V < 5.5V CC DD 9 25 TCM8xxR/S/T/Z: V < 3.6V DD Reset Threshold (Note 2) V 4.56 4.63 4.70 V TCM8xxL: T = +25C TH A 4.50 4.75 T = 40C to +125C A 4.31 4.38 4.45 V TCM8xxM: T = +25C A 4.25 4.50 V T = 40C to +125C A 3.93 4.00 4.06 V TCM809J: T = +25C A 3.89 4.10 V T = 40C to +125C A 3.04 3.08 3.11 V TCM8xxT: T = +25C A 3.00 3.15 V T = 40C to +125C A 2.89 2.93 2.96 V TCM8xxS: T = +25C A 2.85 3.00 V T = 40C to +125C A 2.59 2.63 2.66 V TCM8xxR: T = +25C A 2.55 2.70 V T = 40C to +125C A 2.28 2.32 2.35 V TCM8xxZ: T = +25C A 2.25 2.38 V T = 40C to +125C A Reset Threshold Tempco 30 ppm/C V to Reset Delay, 65 sec V = V to (V 100 mV) (Note 2) DD DD TH TH Reset Active Time Out 140 320 560 msec Period Note 1: Production testing done at T = +25C, overtemperature limits ensured by QC screen. A 2: RESET output for TCM809, RESET output for TCM810. DS21661C-page 2 2004 Microchip Technology Inc.