MUR3060B-BP Micro Commercial Components (MCC)

MUR3060B Features Lead Free Finish/RoHS Compliant(Note 1) Suffix Designates Compliant. See Ordering Information) 30 Amp Halogen Free Available Upon Request By Adding Suffix-H High Frequency Operation Ultra Fast High Surge Forward Current Capability Epoxy Meets UL 94 V-0 Flammability Rating Recovery Rectifier Moisture Sensitivity Level 1 Planar Structure Die and Soft Recovery Characteristics 600 Volts Maximum Ratings Operating Junction Temperature Range: -55C to +175C Storage Temperature Range: -55C to +175C Maximum Thermal Resistance: 0.8C/W Junction to Case Maximum TO-247AD Maximum DC Maximum MCC Device Recurrent Blocking RMS Part Number Marking Peak Reverse Voltage Voltage Voltage K A U T MUR3060B MUR3060B 600V 420V 600V E O D Electrical Characteristics 25C Unless Otherwise Specified C Average Rectified S I 30A T =120C F(AV) C B Forward Current R Peak Forward Surge I 300A 8.3ms,Half Sine FSM Current P G I Instantaneous 2.3V(Max.) V I =30A T =25C J J F F F Forward Voltage 1.95V(Typ.) H Maximum Reverse Q 10A T =25C J I Current At Rated DC R 2 1 500A T =125C J Blocking Voltage Typical Junction Measured at C INCHES MM 180pF J 1.0MHz, V =4V DIM NOTE Capacitance R MIN MAX MIN MAX A 0.602 0.642 15.30 16.30 Dynamic Recovery Characteristics 25C Unless Otherwise Specified B 0.799 0.839 20.30 21.30 C 0.189 0.205 4.80 5.20 31ns(Typ.) I =0.5A I =1.0A F R 0.242 6.15 BSC. D I =0.25A 35ns(Max.) RR E 0.091 0.106 2.30 2.70 Reverse Recovery t rr F 0.768 0.807 19.50 20.50 Time 60ns(Typ.) T =25C J G ----- 0.189 ----- 4.80 T =125C 110ns(Typ.) 0.428 10.88 BSC. J H I = 30 A I 0.075 0.087 1.91 2.21 F 3.4A(Typ.) T =25C Peak recovery J J 0.044 0.054 1.11 1.36 di /dt = 200 A/s F I RRM K 0.189 0.205 4.80 5.20 current T =125C 9.7A(Typ.) J V = 200 V R O 0.073 0.085 1.85 2.15 100nC(Typ.) T =25C P 0.087 0.103 2.21 2.61 Reverse recovery J Q rr Q 0.020 0.030 0.51 0.75 charge T =125C 535nC(Typ.) J R 0.512 0.535 13.00 13.60 S 0.640 0.663 16.25 16.85 Note:1. High Temperature Solder Exemptions Applied, See EU Directive Annex 7a. T 0.134 0.150 3.40 3.80 Internal Structure U ----- 0.287 ----- 7.30 PIN 1 CASE PIN 2 Rev.3-4-04262021 1/3 MCCSEMI.COMMUR3060B Curve Characteristics Fig. 1 - Forward Current Derating Curve Fig. 2 - Maximum Non-Repetitive Peak Forward Surge Current 35 350 30 300 25 250 20 200 15 150 10 100 5 50 Resistive or Inductive Load 8.3 ms Single Half Sine-Wave 0 0 0 35 70 105 140 175 1 10 100 Case Temperature (C) Number of Cycles at 60 Hz Fig. 3 - Typical Instantaneous Forward Characteristics Fig. 4 - Typical Reverse Leakage Characteristics 30 1000 T =175C 100 J 10 10 T =175C J T =125C J 1 T =125C J 0.1 T =25C J 0.01 T =25C J 1 0.001 0.2 0.6 1.8 2.2 20 100 1.0 1.4 40 60 80 Instantaneous Forward Voltage (V) Percent of Rated Peak Reverse Voltage (%) Fig. 5 - Capacitance Characteristics Fig. 6 - Reverse Recovery Waveform and Definitions 500 (3) t rr T =25C I J F t t a b f=1MHz 0 400 (4) Q rr (2) I 0.5 I 300 RRM RRM (5) di /dt (rec)M di /dt (1) F 0.75 I RRM 200 (4) Q - area under curve defined by t (1) di /dt - rate of change of current rr rr F and I through zero crossing RRM 100 t x I rr RRM (2) I - peak reverse recovery current RRM Q = rr 2 (3) t - reverse recovery time measured rr (5) di /dt - peak rate of change of (rec)M from zero crossing point of negative current during t portion of t 0 b rr going I to point where a line passing F 0 5 10 15 20 25 30 through 0.75 I and 0.50 I RRM RRM Reverse Voltage (V) extrapolated to zero current. Rev.3-4-04262021 2/3 MCCSEMI.COM Average Forward Current (A) Instantaneous Forward Current (A) Capacitance Between Terminals (pF) Peak Forward Surge Current (A) Instantaneous Reverse Leakage Current (A)