P6KE6.8 MCC omponents TM 20736 Marilla Street Chatsworth THRU Micro Commercial Components P6KE600(C)A Features Economical series 600WATTS TRANSIENT Available in both unidirectional and bidirectionalconstruction and suffi designates bidirectional type VOLTAGE SUPPRESSOR Lead Free Finish/Rohs Compliant (Note1) Suffix designates Compliant. See ordering information) 6.8 TO 600 VOLTS 600 watts peak pulse power dissipation and 5.8~512V VWM UL Recognized File E331408 Halogen free available upon request by adding suffix-H Epoxy meets UL 94 V-0 flammability rating DO-15 Moisture Sensitivity Level 1 POLARITY: Banded denotes cathode. Bidirectional not marked. WEIGHT: 0.4 Gram(Appx.) MOUNTING POSITION: Any. D Maximum Ratings o Peak Pulse Power Dissipation at 25 C: 600Watts o Steady State Power Dissipatoin:5 Watts at TL=75 C A Cathode Mark for unidirectional only 3/8 Lead Length B t (0 Volts to BV Min.): clamping -12 -9 Unidirectional<1x10 Seconds Bidirectoinal<5x10 Seconds. D o o Operating and Storage Temperature: -55 C to +175 C C APPLICATION Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. DIMENSIONS INCHES MM DIM MIN MAX MIN MAX NOTE A .230 .300 5.80 7.60 B .104 .140 2.60 3.60 C .028 .034 .70 .90 D 1.000 --- 25.40 --- Note: 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. www.mccsemi.com Revision: F 2013/07/18 1 of 5P6KE6.8 thru P6KE600A MCC TM Micro Commercial Components RATINGS AND CHARACTERISTICS CURVES (T = 25 q C unless otherwise noted) A 6000 100 Non-repetitive Pulse Measured at Waveform shown in Fig. 3 Zero Bias TA = 25 C 1000 TJ = 25 C 10 f = 1.0 MHz Vsig = 50 mVp-p 100 Measured at Stand-off 1 Voltage VWM 10 0.1 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms 1.0 10 100 200 V(BR) - Breakdown Voltage (V) td - Pulse Width (sec.) Figure 4. Typical Junction Capacitance Uni-Directional Figure 1. Peak Pulse Power Rating Curve 6 100 60 Hz Resistive or 5 Inductive Load 75 4 50 3 L = 0.375 (9.5 mm) 2 Lead Lengths 25 1 0 0 0 25 50 75 100 125 150 175 200 0 25 50 75 100 125 150 175 200 TL - Lead Temperature (C) TJ - Initial Temperature (C) Figure 2. Pulse Power or Current versus Initial Figure 5. Power Derating Curve Junction Temperature 150 TJ = 25 C tr = 10 sec. Pulse Width (td) is defined as the point Peak Value where the peak current IPPM decays to 50 % of IPPM 100 IPP Half Value - 2 IPPM 50 10/1000 sec. Waveform as defined by R.E.A. td 0 0 1.0 2.0 3.0 4.0 t - Time (ms) Figure 3. Pulse Waveform www.mccsemi.com Revision: F 2013/07/18 2 of 5 Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage,% CJ, Junction Capacitance (pF) PD, Power Dissipation (W) IPPM - Peak Pulse Current, % IRSM PPPM, Peak Pulse Power (kW)