MIKROE-1297 MikroElektronika

2. Soldering the headers Before using your click board, make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 DALI click 2 3 1. Introduction 4. What is DALI DALI (Digital Addressable Lighting Interface) is international standard for network based systems that controls lighting in buildings. Data between MCU and devices is transferred over two-wire differential bus by means of Turn the board upside down so that Turn the board upward again. Make sure asynchronous, half-duplex, serial protocol. bottom side is facing you upwards. Place to align the headers so that they are It is possible to address up to 64 devices in shorter parts of the header pins in both perpendicular to the board, then solder the DALI stand alone systems and more than 64 soldering pad locations. pins carefully. devices as DALI subsystem (gateways) DALI Click is an add-on board in mikroBUS 3. Plugging the board in form factor. Its a compact and easy solution click for adding Digital Addressable Lighting Once you have soldered the headers your Interface (DALI) to your design. It features two board is ready to be placed into desired BOARD optocouplers, push button and screw terminals. mikroBUS socket. Make sure to align the www.mikroe.com DALI Click communicates with target board cut in the lower-right part of the board microcontroller via four mikroBUS lines (RST, with the markings on the silkscreen at the DALI click Manual CS, PWM and INT). The board is designed to use mikroBUS socket. If all of the pins are ver. 1.01 3.3V and 5V power supply. LED diode indicates aligned correctly, push the board all the presence of power supply. the way into the socket. 0 100000 0222216. SMD Jumpers 5. DALI Click Board Schematic Target board microcontroller can receive a signal from DALI peripherals via interrupt pin (INT) or input capture pin (PWM). Jumper J1 enables you to choose between these two ways. J1 is soldered in the INT position by default. There is one zero-ohm SMD jumper VCC DALI Vdali VCC J2 which is used to select between 3.3V or R1 C1 5V power supply. Jumper J2 is soldered in the R4 R2 R3 1K0 10K 1K2 +3V3 +5V 3.3V position by default. 100 LD1 220pF U1 YELLOW VCC +3V3 ICP ICP R5 AN PWM DALI TX DALI TX INT DALI RX RST INT PHY SEL INT 6K8 CS TX TLP181 SCK RX J1 7. Code Examples M1 D1 SCL J2 R7 MISO C2 R6 BSP318S 10K BZX84C005.1 SDA MOSI 10nF 2K2 +5V +3.3V +5V Once you have done all the necessary GND GND LD2 MIKROBUS DEVICE CONN. GREEN preparations, its time to get your click DALI GND board up and running. We have provided Vdali VCC the examples for mikroC, mikroBasic and R10 mikroPascal compilers on our Libstock R9 10K R8 4K7 website. Just download them and you are U2 68K DALI RX DALI Q1 Vdali ready to start. D2 BC846 R11 390 TLP181 Q2 R12 BC856 CN2 10K .com BAW56 R14 VCC 2 1 270K R13 Q3 100K BC846 R16 R15 10K 1K DALI C4 T1 G1 PHY SEL 100nF MB2S 8. Support DALI DALI GND DALI GND MikroElektronika oers ff Free Tech Support (www.mikroe.com/esupport) until the end of product lifetime, so if something goes wrong, we are ready and willing to help MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document. Specification and information contained in the present schematic are subject to change at any time without notice. Copyright 2012 MikroElektronika. All rights reserved. C3 100pF 4 3 E1 10uF D3 BZX84C22 E2 47uF/25V