2. Soldering the headers Before using your click board , make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 XBEE click 2 3 4. Essential features XBee click is network-compatible with other devices that conform to ZigBee standards. The module operates at the 2.4-2.5GHz band, has a wireless range of up to 60m indoors, or up to 1.2km outdoors (line-of-sight). The RF data rate is up to 250 Kbps. To simplify deployment, the click features a commissioning button Turn the board upside down so that Turn the board upward again. Make sure and an associated LED. They allow you to the bottom side is facing you upwards. to align the headers so that they are issue simple configuration commands with Place shorter pins of the header into the perpendicular to the board, then solder the subsequent button presses (joining or leaving appropriate soldering pads. pins carefully. networks, self-identification, restoring default values etc.) 1. Introduction 3. Plugging the board in XBee click carries the Xbee and Zigbee- compliant XB24CZ7PIS-004 module with click Once you have soldered the headers your a PCB antenna from Digi International. The board is ready to be placed into the desired module provides wireless connectivity to BOARDS mikroBUS socket. Make sure to align the end-point devices in ZigBee mesh networks. www.mikroe.com cut in the lower-right part of the board with The board can communicate with the target the markings on the silkscreen at the MCU either through the mikroBUS UART mikroBUS socket. If all the interface (TX, RX, RTS i CTS), or SPI (MISO, XBEE click Manual v101 pins are aligned correctly, MOSI, SCK, CS). Additional functionality is provided by, Reset, and ATTN-DTR pins. Uses push the board all the way 0100000090060 3.3V power supply only. into the socket.8. Code examples 5. Schematic Once you have done all the necessary preparations, its time to get your click board up and running. We have provided examples for mikroC , mikroBasic and mikroPascal VCC-3.3V VCC-3.3V VCC-3.3V VCC-3.3V XBee RF Module T2 compilers on our Libstock website. Just R4 37 XBEE Reserved 2K2 36 download them and you are ready to start. R3 R2 RF 35 1K 10K GND 1 34 GND Reserved LD2 2 33 VCC DIO0/AD0/CB TX 3 32 VCC-3.3V DOUT/DIO13 DIO1/AD1 Q1 RX 4 31 DIO14/DIN/nCONFIG DIO2/AD2 PDTC114EU 5 30 DIO12 DIO3/AD3 RESET N 6 29 RTS nRESET DIO6/nRTS R1 .com RTS CTS 7 28 ASSOC AN PWM DIO10/ RSSI WP M/PWM0 DIO5/ASSOC RESET N ATTN-DTR J1 8 27 RST INT DIO11/PWM1 VREF CS TX 9 26 R2 CS TX Reserved DIO9/On nSLEEP SCK RX ATTN-DTR DTR 10 25 CTS SCK RX DIO8/nDTR/SLEEP RQ DIO7/nCTS SDO 11 24 SCL GND DIO4 MISO SDI ATTN 12 23 SDA DIO19/SPI nATTN Reserved MOSI 13 22 +3.3V +5V GND GND GND GND C3 9. Support MIKROBUS DEVICE CONN. 100nF VCC-3.3V VCC-3.3V VCC-3.3V MikroElektronika offers free tech support R1 2K2 (www.mikroe.com/support) until the end of LD1 the products lifetime, so if something goes wrong, were ready and willing to help 6. Dimensions 7. ATT/DTR jumper 10. Disclaimer The ATT/DTR jumper is MikroElektronika assumes no responsibility mm mils for setting the interrupt or liability for any errors or inaccuracies feature, depending on that may appear in the present document. LENGTH 57.15 2250 whether SPI or UART is Specification and information contained in used for data transmission WIDTH 25.4 1000 the present schematic are subject to change (ATT for SPI, DTR for UART). HEIGHT* 5.33 210 at any time without notice. 57.15 / 2250 mils * without headers Copyright 2015 MikroElektronika. All rights reserved. 25.4 mm / 1000 mils SCK 14 DIO18/SPI CLK CS 15 DIO17/SPI nSSEL SDI 16 DIO16/SPI SI SDO 17 DIO15/SPI SO 18 Reserved 19 Reserved 20 Reserved 21 Reserved C1 100nF C2 10uF