MIKROE-2032 MikroElektronika

2. Soldering the headers Before using your click board , make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 PULSE click 2 3 4. Essential features The frequency of PULSE click is configured in two steps. First select between four frequency bands by using the frequency selector - a circular central switch in the middle of the board. Starting from the six-o- clock position and moving counter-clockwise in quarters, it has 4 options: 0) Up to 100 Hz 1) Up to 1 kHz 2) Up to 10 kHz and 3) Up Turn the board upside down so that Turn the board upward again. Make sure to 100 kHz. After you select the appropriate the bottom side is facing you upwards. to align the headers so that they are position, use the onboard potentiometer to Place shorter pins of the header into the perpendicular to the board, then solder the fine-tune the desired output frequency. appropriate soldering pads. pins carefully. 1. Introduction PULSE click is a pulse generator with an 3. Plugging the board in adjustable frequency. It carries the NEN555 precision timer capable of producing highly click Once you have soldered the headers your accurate time delays, and the output can board is ready to be placed into the desired be sent to the MCU through the OUT pin, BOARDS mikroBUS socket. Make sure to align the cut (default mikroBUS AN pin) or an interrupt www.mikroe.com in the lower-right part of the board with the (INT pin) or an interrupt (INT pin). An extra markings on the silkscreen at the mikroBUS output pin above the mikroBUS socket is socket. If all the pins are aligned also available. Designed to use either a 3.3V PULSE click Manual v100 PULSE click Manual v100 correctly, push the board all the or a 5V power supply. way into the socket. 01000000924538. Code examples 5. Schematic Once you have done all the necessary +3.3V +5V +5V +5V +5V +5V R2 R6 U1 C1 preparations, its time to get your click board 2K2 3K3 100nF OUT 1 8 AN PWM GND VCC INT TG-TH 2 7 DISCH RST INT TRIG DISCH up and running. We have provided examples OUTA 3 6 LD2 CS TX OUT THRES Ra 4 5 SCK RX RESET CONT SCL MISO for mikroC , mikroBasic and mikroPascal NE555 R4 SDA OUTA Q1 MOSI C2 P1 +3.3V +5V DMG3420U 10K 10nF 10 GND GND compilers on our Libstock website. Just MIKROBUS DEVICE CONN. R5 P2 GND GND GND 1M 100K download them and you are ready to start. GND GND +5V VCC-OUT VCC-OUT GND GND U2 Use a screwdriver to adjust the R7 R3 C7 C8 +5V output sigal frequency: 51 1 6 2K2 100nF 100nF VCCA VCCB 2 5 GND DIR DISCH OUTA 3 4 OUTB OUTB clockwise counter clockwise A B R1 UP DOWN .com HD1 2K2 SN74LVC1T45 OUTB R8 1 Total frequency range: Q ~ 0.05Hz - 100kHz 51 2 GND GND Rb LD1 GND P3 10K +5V VCC-OUT +3.3V J1: Output function settings GND P4 9. Support Use output voltage signal as: 100K - interrupt (INT) J1 - general purpuse analog/digital J2 INT (OUT) MCU input OUTB TG-TH OUT J2: Output voltage level settings SW1 MikroElektronika offers free tech support SW1: Frequency 3 2 0 range selector: (www.mikroe.com/support) until the end of C C Output voltage signal parameters: position 0: 100Hz 1 3 position 1: 1kHz 2 1 the products lifetime, so if something goes position 2: 10kHz 0 tH=0.693(Ra+Rb)C position 3: 100kHz CS-7 wrong, were ready and willing to help tL=0.693(Rb)C 1.44 tH tL frequency= C6 C5 C4 C3 (Ra+2Rb)C T 0.1uF 1uF 10uF 100uF Units: frequency kHz tH, tL ms Ra, Rb Kohm C uF GND GND GND GND 6. Dimensions 7. SMD jumper 10. Disclaimer MikroElektronika assumes no responsibility PULSE click features mm mils an SMD jumper or liability for any errors or inaccuracies (zero ohm resistor) that may appear in the present document. LENGTH 42.9 1690 that lets you switch Specification and information contained in WIDTH 25.4 1000 between a 3.3V or a the present schematic are subject to change 5V power supply. HEIGHT* 3.9 154 at any time without notice. 42.9 mm / 1690 mils * without headers Copyright 2015 MikroElektronika. All rights reserved. 25.4 mm / 1000 mils