LOW NOISE, HIGH IP3 Monolithic Amplifier PMA-5456+ 50 0.05 to 6 GHz THE BIG DEAL y Ultra Low Noise Figure, 0.8 dB y High IP3, 34 dBm typ. 1GHz y Wideband, up to 6 GHz y Low Additive Phase Noise y Suitable for low phase noise applications Generic photo used for illustration purposes only CASE STYLE: DQ849 APPLICATIONS +RoHS Compliant The +Suffix identifies RoHS Compliance. See our web site y Cellular for RoHS Compliance methodologies and qualifications y ISM y GSM y WCDMA y LTE y WiMAX y WLAN y UNII and HIPERLAN PRODUCT OVERVIEW PMA-5456+ is a high dynamic range, low noise, high IP3, high output power, monolithic amplifier. Manufactured using E-PHEMT* technology enables it to work with a single positive supply voltage. Unconditionally stable over the operating frequency. KEY FEATURES Feature Advantages Ultra Low Noise, 0.8 dB Outstanding Noise Figure, measured in a 50 Ohm environment without any external matching Combining Low Noise and High IP3 makes this MMIC amplifier ideal for Low Noise High IP3, 34 dBm Receiver Front End (RFE) because it gives the user advantages at both ends of the dynamic range: sensitivity & two- tone spur-free dynamic range At only 60mA, the PMA-5456+ is ideal for remote applications with limited available power or densely packed applica- Low Current, 60 mA tions where thermal management is critical. Operating over a broadband the PMA-5456+ covers the primary wireless communications bands: Cellular, PCS, LTE, Broad Band WiMAX Internally Matched No external matching elements required to achieve the advertised noise and output power over the full band MCLP Package Low Inductance, repeatable transitions, excellent thermal pad Max Input Power, +20 dBm Ruggedized design operates up to input powers of +20 dBm without the need of an external limiter Low, small signal operating current of 60mA nominal maintains junction temperatures typically below 125C at 85C High Reliability ground lead temperature Low additive phase noise, typically Ideal for low phase noise synthesizer applications -161 dBc/Hz 10 KHz offset *Enhancement mode Pseudomorphic High Electron Mobility Transistor REV. G ECO-011027 PMA-5456+ TH/RS/CP/AM 211203 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales minicircuits.com PAGE 1 OF 5LOW NOISE, HIGH IP3 Monolithic Amplifier PMA-5456+ (1) ELECTRICAL SPECIFICATIONS AT 25C, ZO=50 (REFER TO CHARACTERIZATION CIRCUIT, SEE FIG. 1) Parameter Condition (GHz) Min. Typ. Max. Units Frequency Range 0.05 6.0 GHz DC Voltage (V ) 5.0 V d (6) DC Current (I ) 47 60 80 mA d DC Current (I ) 2.4 mA Rbias 0.05 1.8 0.5 0.8 1.0 0.8 2.0 1.0 1.3 Noise Figure dB 3.0 1.3 4.0 1.6 5.0 1.9 6.0 2.4 Additive Phase Noise, 2.0 GHz, 10KHz offset -160.5 dBc/Hz 0.05 26.0 0.5 23.2 1.0 19.4 2.0 12.7 14.4 15.8 Gain dB 3.0 11.1 4.0 9.2 5.0 7.3 6.0 5.8 0.05-0.5 10.0 Input Return Loss dB 0.5-6 7.0 0.05-0.1 15.0 Output Return Loss dB 0.1-6 20.0 0.05 31.8 0.5 33.0 1.0 34.0 2.0 36.0 Output IP3 dBm 3.0 36.4 4.0 36.4 5.0 37.2 6.0 37.2 0.05 22.0 0.5 21.7 1.0 21.7 2.0 21.6 (2) Output Power 1 dB compression dBm 3.0 21.5 4.0 21.7 5.0 22.0 6.0 22.1 (3) DC Current Variation vs. Temperature -0.072 mA/C Thermal Resistance 128 C/W (4) MAXIMUM RATINGS (1) Measured on Mini-Circuits Characterization test board TB-502+. Parameter Ratings See Characterization Test Circuit (Fig. 1) (5) (2) P1dB specified with external current limiting of 70mA Operating Temperature -40C to 85C (3) (Current at 85C - Current at -45C)/130 Storage Temperature -55C to 100C (4) Permanent damage may occur if any of these limits are exceeded. These maximum ratings are not intended for continuous normal operation. Channel Temperature 150C (5) Defined with reference to ground pad temperature. (6) Specified DC current consumption is under small signal conditions. Current will increase with DC Voltage (Pad 6) 6V input RF Power. To maintain maximum current consumption, external DC current limiting Power Dissipation 500mW circuits are required on Vd line. (7) Maximum input power is specified based upon external Vd current limiting of 80 mA. DC Current (Pad 6) 100mA Maximum input power will degrade without external current limiting. Bias Current (Pad 7) 10mA (7) Input Power 20dBm (4) Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. (5)Measured on Mini-Circuits test board, TB-736+ www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales minicircuits.com PAGE 2 OF 5