1.25G Etherenet Multi-rate 10/100/1000BASE-T Copper SFP Transceiver TRPRG1VA1x000E2G Pb Product Description TRPRG1VA1x000E2G Copper Small Form Pluggable (SFP) transceivers are high performance, cost effective and compliant with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE 802.3-2002 and IEEE 802.3ab. The module has two interfaces: the host interface and the MDI interface. The MDI interface provides 1000Base-T connectivity over the Category-5 cable. The host interface provides the data transfer over the 1.25 GHz PECL differential interface to the host board and control and configuration functions through the serial management interface. The module supports 1000Mbps full duplex with 5-level Pulse Amplitude Modulation (PAM) signals. The default mode of operation after power- up is 1000Base-T, full duplex, over SERDES Interface. All four pairs in the Features cable are used with symbol rate at 250Mbps on each pair. The module Compatible with IEEE 802.3z, IEEE 802.3u, IEEE provides standard serial ID information compliant with SFP MSA, which 802.3ab can be accessed with address of A0h via the 2wire serial bus interface. The physical IC can also be accessed via 2-wire serial bus at address ACh. Compatible with SFP MSA Hot-pluggable SFP footprint The transceivers operate from a single +3.3V power supply over an RJ-45 connector assembly operating case temperature range of 0C to +70C (Commercial) , -40C to +85C (Industrial) or -5C to +85C (Extended). The housing is made Access to physical layer IC via 2-wire serial bus of metal for EMI immunity. TX Disable Auto MDI/MDIX TDR functionality support 1000Base-T,full duplex default operating mode over SERDES interface 10/100/1000Base-T operation on platforms supporting SGMII Metallic enclosure for low EMI Rohs6 compliance Unshielded cable support FCC Class B compliant Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Storage Temperature T - 40 + 85 C ST Commercial 0 + 70 1 Case Operating Temperature Extended T - 5 + 85 C OP Industrial - 40 + 85 1 Measured on top side of SFP module at the front center vent hole of the cage S0306. Rev.03. (web) 2016-12-14TRPRG1VA1x000E2G General Specifications Parameter Symbol Minimum Typical Maximum Units Operating Data Rate B 10 - 1000 Mb/s 1 Cable Length L - - 100 m 1 Category 5 UTP Electrical Power Supply Characteristics Parameter Symbol Minimum Typical Maximum Unitts Input Voltage V 3.13 3.3 3.47 V CC Supply Current I - - 375 mA CC Power Consumption P - - 1.2 W W Inrush Current 1 I - - 30 mA in-rush 1 The maximum inrush current during the hot plugging shall not exceed 30 mA. Input Characteristics Parameter Symbol Minimum Typical Maximum Units Input differential impedance R 90 100 110 ohm IN Single ended data input swing V 250 - 1200 mV in, pp Disable V 2.0 - Vcc V IH TX Disable Enable V Vee - Vee +0.8 V IL High V 2 - Vcc V ihmin MOD DEF1 Low V Vee - Vee +0.8 V ilmax High V 2 - Vcc V ihmin MOD DEF2 (when host drives) Low V Vee - Vee +0.8 V ilmax Output Characteristics Parameter Symbol Minimum Typical Maximum Units 1, 2 Single ended data output swing V 185 - 600 mV out, pp, Data output rise time (20%-80%) T - - 300 ps R Data output fall time (20%-80%) T - - 300 ps F Fault V N/A - N/A V Fault TX Fault 3 Normal V Vee - Vee +0.5 V Normal Fault V N/A - N/A V losFault LOS 3 Normal V Vee - Vee +0.5 V losNormal High V N/A - N/A V ihmin MOD DEF0 3 Low V Vee - Vee +0.5 V ilmax High V 2.3 - Vcc V ihmin MOD DEF2 (when SFP drives) Low V Vee - Vee +0.5 V ilmax 1 Measured with 100 Ohms differential termination. 2 Old requirement were 350/800 mV. Changed to be compliant with SFF-8431 standard for 10G port EDC applications (1G support in 10G capable SFP+ ports). 3 The signal is grounded on the SFP module. S0306. Rev.03. (web) 2016-12-14 Oplink Communications, LLC 2